Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi ,
I'm intrested in using the BLE UART apllication provided by Nordic for the nRF51 422 developpement kit and I have a little question to ask and please forgive its simplicity...
Environment is a PCA10040 v1.1.0, measuring current with a Rigol DS1104B over a 10 Ohm resistor.
I'm using the ble_pwr_profiling example from nRF5 SDK v11. I've programmed...
Hi,
i;m trying to build the "nrf52-ble-app-lbs" example which i downloaded from git hub github.com/.../nRF52-ble-app-lbs.
I followed the instructions in the README file...
I want to connect to the wired sensor NRF51822 board, whether it is possible to adjust the findings for the closure, they sent a message to the application?
Hi, I've recently switched from the older SDK 6 to SDK 9. However, I am unable to get my NRF51822 working with any of the example projects. I've managed to compile the projects...
Hi, I am working on eddystone project i.e nrf5-sdk-for-eddystone-master which is newly released by nordic. And I set URL,UUID and TLM frames successfully but when I trying...
Hello,
I am encountering a very strange problem with the Timeslot API.
I am developing with s130 and using the timeslot example provided by Nordic to
send data revived...
So far I've been prototyping everything on an Arduino Zero connected to a nRF24. Is switching to an nRF51822 an option for me? or will I have to switch my entire code to work...
I need to communicate with several nrf modules, 1 rx and at least 2 rx. I started with nrf24l01 but it has no rssi. For that reason i bought nrf51822.
What i have to do to...
hi,
i have doubt regarding NRF 51822BEACON KIT [pca20006 board],
......i want to configure it in all ble modes [central,periperal,broadcaster,listener],
how can i do...
Hi,
I want to add DFU OTA feature for my project, I use SDK 6.1.0 and S110 7.1.0, I found a sample Bootloader code for different version of SDK (SDK 6.0.0), from Github...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
From the SDK documentation
infocenter.nordicsemi.com/index.jsp
"...platform.h is a use case and
system specific file that can contain
defines and routines needed...
Hello Nordic People,
I am working on making concurrent operation of ESB and BLE to set up sensor network. Currently, the initial set up has been implemented in such that...
Hello,
I use GCC as IDE because I must(though I debug perfectly via Keil v5). I migrated to eclipse GCC by the tutorial published here on 'Devzone'. I added some C codes...
