void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hi all Nordic developers,
I am currently working on an application using a sensor (the temperature sensor) on a Smart beacon kit, which must connect and send data to a...
Hi all,
What's the difference between the Beacon Transmitter Sample Application example given in nRF51 SDK and the beacon firmware provided in the beacon kit? Are there...
Hello,
I have a nRF 52 preview board (PCA10036) and would like to use ETM trace to enable the "execution profiling" in Keil v5.
After I enable the trace and ETM trace...
Hi,
I am facing hardfault when i try to enable low power in a ble application. i want to enable trace on my PCA10040 board to find out the cause of this hardfault. can...
Hi,
We are using our own custom nRF52832 based board, with revision B silicon however we are having trouble getting trace functionality to work.
Our code uses the Nordic...
Hi,
I am going to design a new product around nRF51422 and I am planning to buy the nRF51 DK but I am really confused about the sw I need for development and additional...
I found this recent Q&A very helpful on the topic of reading voltage on analog hardware pins via the ADC: devzone.nordicsemi.com/.../
In that Q&A, a helpful Nordic person...
I want to use the MultiActivity Example with the nRF52 with GCC and Eclipse.
In the documentation I ve read that S130 and S132 are supported, but in the directory of the...
When I using the UART port, if I float the port after init the UART it will restart the code, is it need a external pull-up resistor? How about the value?
A quick one, where do I find a list of the err_codes? I have had a look in the documentation and I was expecting to find a table of them, but I couldn't locate one.
Thanks...
Hello!
I am trying to send a notification to a peer device when a certain event occurs. To do so, I'm using the same procedure as with every other characteristic with enabled...
I used the example of the ble_central\ble_app_uart_c and ble_peripheral\ble_app_uart.
It seems no problem for operation when I check only this example.
But I modified this...
Hello Everyone ,
I ahve deveoped the custom board using NRF51SOC and i have flashed the custom board by usign P20 Connector referred below figure now i would like to debug...
If I let the SoftDevice write to my variables directly by having the characteristics point to my app's variables through BLE_GATTS_VLOC_USER - when are these variables actually...
