Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Hi
I am using the ESB sample and want to use the RADIO_MODE_MODE_Nrf_250Kbit PHY, but I will get not support after requiring:
Can we still use 250 PHY in nRF54L15 ESB...
Hi,
After upgrading from NCS 2.5.2 to NCS 3.1.1, I get quite frequent MPSL assertion errors on a nRF52840. Can you shed some light into what this assertion error is about...
The datasheet list
A25, B12, B26, D2, F2, G1, H2, J31, K2, T2, AG31, as N.C.
I have not been able to read exactly what N.C. implies: It could be: "do not connect", "no...
Hello,
I am working a project that uses the NRF52840 dongle with BLE and UART to communicate to two separate devices while going through temperature cycles. I have not...
My device supports both Central and Peripheral roles. By default, it works in Peripheral mode. When the device connects in Peripheral mode, I want the following behavior:...
Hello Nordic team,
I am working on an nRF52840 project using nRF Connect SDK (Zephyr-based, v2.x / v3.x) and I would like to clarify the official support status of a specific...
Running doxygen nrfx.doxyfile
Per the README.md in C:\ncs\nrf-bm\v1.0.0\modules\hal\nordic\nrfx\doc fails.
See output below.
C:\> C:\apps\doxygen-1.16.1.windows.x64...
Hi there.
we have firmware that was running on nRF5340 MCU. we had decided to migrate to the nRF54H20 MCU because of flash size limitation. this MCU was announced with 2MB...
I am trying to connect to two reflectors and sound only from 1 device so far the connection and soundnig works well for first set of connection and after a disconnectio, the...
I am modifying the Qorvo UWB SDK to add BLE operations. I have posted a couple other topics about different issues..
I have ported my code to the latest Qorvo SDK, They...
With NCS 3.0 and the nRF54L15, even after applying patches, the power consumption anomaly can still be reproduced at the edge of the NFC range. The power consumption anomaly...
We are using zephyr's conn_mgr to manage the network connection. From what I can tell, if I have set CONFIG_NRF_MODEM_NET_IF=y and NRF_MODEM_LIB_NET_IF_CONNECTION__PERSISTENCE...
I want to try the tdm function on the nrf54lm20 dk.
But i have encountered problem in the first step.
I do not know how to add the tdm port and assign the pin.
Whin...
Hi.
We are using nRF Connect SDK v3.2.1 and nRF52832 MCU.
Our current internal flash memory mapping is like below,
mcuboot + mcuboot_primary (application) + mcuboot_secondary...
Mass Provisioning of Nordic BLE Mesh Nodes - Mesh Networks - nRF5 SDK guides - Nordic DevZone
We are evaluating this mass‑provisioning approach. Is there an alternative...
