Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
Greetings,
I want to change Device name on Advertising. Is that possible? I am using nrfSDk52832, I want when some state of Switch is change, to change advertising name...
I am new to this device, so please bear with me during the inevitable simple misunderstandings! I am scanning for bluetooth devices and getting sensible numbers of devices...
Hi, I have a custom board with an ISP1807 onboard. We'd like to optimize the production process, especially the programming process. We currently use the nrf52840 dk board...
I have a small demo, based on the hello world example, where I have also enabled gpio_keys. I can run this on the nRF52-DK, nRF54-DK but when I come to run it on my custom...
I have seen a few posts including:
Change advertised name (Bluetooth) - Nordic Q&A - Nordic DevZone - Nordic DevZone (nordicsemi.com)
NCS bt_set_name() - Nordic Q&A...
Hello everyone,
I am using NRF5340-DK for my project and I am trying to combine X509 certificates (using MBEDTLS) with RSA operations (using PSA). This is my current proj...
I am working with the wisblock 4631 from rak, that contains an NRF52840. I am working with the Zephyr infrastructure and uploading code via the Nordic extension for VS Code...
Hello,
We have developed a custom System-on-Module based on the nRF9151 SiP and are ready to begin testing its NTN (Non-Terrestrial Network) capabilities.
Following the...
Thingy91I: Is there a sample project accessing the environmental sensor (BME688) ?
If not, perhaps a project to access a device via I2C by the nrf5340 SIP.
A related question...
I am trying to use the HTTPS_Client example but I am struggling to get it working. It returns 200 unmodified, which makes me think everything is working in terms of the board...
Hi, I’m trying to provision a P‑256 key pair into the KMU at runtime on an nRF54L15 (SDK v2.9.1) but psa_generate_key consistently returns PSA_ERROR_NOT_SUPPORTED, even when...
Hi,
In our project, we are planning to use the nRF9160 for both LTE-M and Wi-Fi. Thus, we have connected the nRF9160-DK to the nRF7002-EK in the developing phase as we read...
Hello,
As the LE Audio controller for nRF5340 library is deprecated in favor of the Nordic Semiconductor’s standard Softdevice Controller. We have started to use the Softdevice...
I am using the nrf54l15-dk. I had a look at the datasheet and it shows that a watchdog reset does not reset the GRTC. On my code, I tested that and I see that GRTC resets...
