I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hallo, we are evaluating the UART peripheral of the nrf54l15. As a first step, we are trying to get two DK to communicate with each other, unfortunately without success. ...
Hi all,
I'm looking at an issue and I can't get my head around it. I clearly do something wrong here but I'm stuck.
On our nRF54L15 DK we have a program that can show...
Dear Teams,
I’m using an nRF9151DK board running a simple firmware (example link: github.com/.../ subsys /pm/ device_pm ).
I connected a Power Profiler Kit II (PPK2) to...
Hi,
When I was developing, I found that the matter sample is a little different from the Bluetooth sample .
I want to disable CONFIG_THREAD_LOCAL_STORAGE in the Bluetooth...
Using a slightly modified version of the Zigbee Light Bulb sample app from the current samples compiled using nRF Connect for VSCode on a Mac and programmed to a nRF52840DK...
Hello,
I started off doing a v3.1.1 build and got this serious warning message
warning: BT_CTLR_DTM_HCI (defined at subsys/bluetooth/controller/Kconfig.dtm:14) was assigned...
This is a bug report for nRF Connect SDK 3.1.1.
The zsock_poll() method and hence also the poll() wrapper method https://docs.nordicsemi.com/bundle/zephyr-apis-3.1.1/page...
When following through the process described on GitHub for the NCS_SERIAL_MODEM I get an error during the build. I am following the steps described in the readme exactly as...
Hello Nordic Team,
We have developed a custom PCB using nRF9151 and nPM1300 . Sometimes, the PMIC powers up and works normally; other times it doesn’t start at all. It occasionally...
Hi All
I have a question here.gatt Characteristic uuid has been Modified After the equipment has been in run for some time.
Current conditions of the equipment:
1.The...
Hi all,
I'm trying to use SPI Slave on a proprietary Hardware that use Ezurio BL54L15 (that contain a Nordic nRF54L15 chip). The environment is VSC + nRF Connect SDK 3.1...
Hello Nordic team,
I’m using the Mikroe nPM1300 PMIC Click Board (based on the Nordic nPM1300 PMIC ) with an ESP32 over I²C to charge a Li-ion battery.
Setup details:...
Hi,
May I know if the ncs add-on sdk-ant also supported nRF52833 because it is not mentioned in the list. Thanks.
Compatibility — ANT for nRF Connect SDK documentation...
Hi,
I need to use GRTC channel 0 in a nRF54L15 project. Channel 0 is special. It is the channel that the INTERVAL register controls. `zephyr/boards/nordic/nrf54l15dk/nrf54l_05_10_15_cpuapp_common...
