Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Dear sirs,
My purpose is to transmit stereo HiFiaudio from one source to two speakers wirelessly.
The speakers have their own power amplifier.
The problem is that the...
Hi,
I am getting started in a project where I am using the nrf52840 dongle to develop. One of my goals is to keep the toolchain up to date, so I started working with the...
Hi Nordic team,
I am working on BLE Channel Sounding (Initiator + Reflector) on nRF54L15 using Zephyr / nRF Connect SDK v3.1.1.
I would like to clarify the expected behavior...
Looks like the new project behavior changed between 3.2.0 and 3.2.1. When creating a new project with the copy function, in 3.2.1 it no longer copies the source code to the...
Hi Nordic
i am working with nrf52832 and nrf52840
After migration from ncs2.9.2 to 3.0.2 my device (end point) has an issue with pairing to one of the gateways (the gateways...
We have an issue receiving unicast packets with default wifi low power mode.
When CONFIG_NRF_WIFI_LOW_POWER=y is enabled, unicast packets (DHCP Offer/Ack, DNS responses...
I performed the following steps:
1. I installed nRF Connect for VS Code Extension Pack in VS Code
2. I created a new application by copying a sample (Bluetooth LE HIDS...
I'm building my small board with nrf52810, buyed 10 chips from seller, it is cheaper relatively, I know it is used chip.
7 of them burned successfully,but 3 of them raise...
I am having difficulty getting Thread Block-wise Transfers working correctly using the API from NCS v2.0.0. It was my understanding that the otCoapSendRequestBlockWise function...
Hello,
I'm implmenting firmware updates over BLE, using a nRF5340DK, nRF Connect SDK v3.2.1, and an Android phone.
I can use the nRF android app, but how can I do this...
Hi There,
Our product is using NRF52810. Now we need to do BLE CE certificate to enable our product sales in foreign country.
I am using "radio test" program for the certification...
Hello everyone,
I am currently working with the nRF54L15 and implementing Thread commissioning using TCAT (Thread Commissioning over Authenticated TLS) .
Setup Overview...
After updating from SDK V2.1.3 OTA to SDK V2.9.0, iOS cannot correctly read data such as the model number, but Android can read it normally.
Turn off Bluetooth in the...
I was thinking to use mpu to make a "safe task" that use nrf52840 for the ble NUS comunication and I use the "safe task" to verify the timeout and the CRC of the message ...
