Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
I have discovered a serious issue with Bluetooth connectivity on iOS 26.
My device use nrf52832 and sdk15.3, it consistently disconnects just a few seconds after a successful...
Hello everyone,
I have tried several different approaches to solve this issue, but I have not been successful so far.
My goal is to generate an interrupt when the LIS2MDL...
Hi,
We have sent out our product (includes the nRF9160 SiP and an nRF52840) for EMC testing and the test lab is asking for the following:
nRF9160 LTE Cat M1 and NB...
We have noticed an issue with our device built on nRF5 SDK + nRF52832 when connected to iOS 26.
Initially after connection, everything is ok. Then we attempt a connection...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
Hello Nordic Team,
I am designing a custom PCB using the nRF52840 and a PCB trace antenna for 2.4 GHz BLE.
In my current design:
I will take nRF52840 dongle antenna...
I am using the nRF5 SDK, nRF52833, and nRF52832.
I flashed the following two demos:
nRF5_SDK_17.1.0_ddde560\examples\ble_central\ble_app_uart_c\pca10100\s122 (nRF52833...
Hello,
We are currently developing a Zigbee product using nRF Connect SDK v2.8.0 . While reviewing the release notes for NCS v2.9.0 , we noticed two critical bug fixes related...
Hi
We used ALA321C3 like antenna for the chip nRF54L15 , but we have a little probleme that the signal of it is not stable.
So we need your teams to help us.
And we...
While debugging the code with Nrf connect extension in VS code , code get stuck at the start only does not go any where getting the SIGNTRAP error continuous
I am trying to retrieve the PIN / HWID required for nRF Cloud onboarding using the AT command AT%XDEVICEID , but I am unable to get a valid response from the modem.
However...
Hello,
I have downloaded the newest Zigbee R23 SDK (v1.3.0).
When I use the feature inside VS Code: "nRF Connect" -> "Create a new board" to create my custom board...
Only information I can get back for the nPM1304 datasheet from Nordic's website is an html version that's missing all the normal sections you expect in a datasheet. Things...
Hello, I am currently experiencing an issue with the 802154_phy_test example on the nRF54L15-DK board, and I would appreciate your technical support.
[ Environment ]
...
Hi,
I'm designing a battery-powered active RFID timing base station and I'm evaluating the nRF54L10 for it. Patrick from Nordic suggested the nRF54L series over the older...
