Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hi,
How to implement two sets of SPI on the NCS v3.0.0 nRF54L15 P2 port? If it can be achieved, please provide the corresponding IO ports for these two sets of SPI.
Kind...
Hi，
We are designing a cellular antenna based on the Thingy91x reference, which needs to support all frequency bands of the nRF9151 cellular module. The antenna tuning switch...
Hi Nordic team,
I am using nRF54LM20DK with NCS v3.3.0 and trying to enable QSPI.
However, there is no &qspi or &qspi20 node in DTS, and adding it causes build errors...
Hi Nordic team,
We are designing a custom board using an nRF54L15 together with an nRF7002 WLCSP.
Our board has a single 3.3 V power rail. We would like to confirm the...
Hi,
AI says this is a known issue, but I want a much stronger explanation of why this scenario breaks. I run the server program on the nRF52840. I understand that it is...
Hello!
I am stress-testing the nRF54L15 devkit by sending it random-sized chunks of data over UART at 921600 baud, which the devkit code receives using the asynchronous...
In the absence of a QGAA reference, is there anything to be aware of when designing a QGAA board?
For example, with the nRF52840, the WLCSP and QFN references used different...
Hi Nordic team,
I am working on nRF5340 and trying to enable MCUboot serial recovery DFU in single-slot mode with both signing and encrypted images.
Environment: 1. SoC...
Summary
The Zephyr RRAM driver drivers/flash/soc_flash_nrf_rram.c does not pass NS-side reads of TF-M secure flash through soc_secure_mem_read when the device tree uses...
I am interfacing a TLV320AIC3204 codec EVM with an nRF54L15 board using I2S.
The codec EVM default configuration is working correctly. I verified audio on the EVM side....
Bluetooth physical layer Direct Test Mode testing is used to verify BLE low-level RF transceiver performance. The required software is nRF Connect for Desktop V3.7 + Direct...
Hi,
When starting nRF Connect for VS Code, SDK v3.3.0, the message Unable to resolve configuration with compilerPath: "C:\ncs\toolchains\fd21892d0f\opt\zephyr-sdk\arm-zephyr...
Hi,
We have two option to use Flash memory,
Option 1: We are planning to use Flash Memory on the SPI bus shared with the NRF7002. Kindly confirm whether this configuration...
Hello Nordic Team,
We are trying to test an I2S DAC (MAX98357A) with the nRF54LM20B EVK . Could you confirm if this is supported and which sample application is recommended...
