Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hey there!
I am facing a very frustrating issue, where my nRF54L15 (custom board) BLE peripheral just won't appear in mobile apps.
For example, right now I am trying to...
Hello, I am currently developing UART communication firmware for the nRF52805, but I am encountering issues with performing DFU firmware updates.
Below are the details of...
Hi,
I'm reading 1 byte of data from a Macronics MX25R64, but the execution speed of the read operation varies depending on the SDK version.
With SDK 3.1.1, it's possible...
Hello,
I have some trouble to identify my custom nrf52832 board in the VSCODE.
To program the board I am using nrf52840dk, and connect it to my board as follows:
...
It seems there might be a small issue with the TF-M GPIO MCU-select IOCTL plumbing on nRF54L — specifically when a non-secure app tries to configure sQSPI GPIOs (and presumably...
Hi,
I am doing a bare‑metal USB test on the nRF54LM20A DK and I see the CPU hang as soon as I read from NRF_USBHSCORE . I’m using:
Chip: nRF54LM20A (DK)
Library...
I am taking a course on academy.nordicsemi.com but every time I try to log in it says "Incorrect username or password. Please try again":
I then use "Forgot your password...
Hello,
I using ncs v3.1.1 SLM on nrf9151 to send messages to a CoAP server. It seems nrf9151 by default uses AES_128_CBC_SHA256 even though on the server side, we have given...
I measured the power consumption of the BLE RX using the nRF54L15.(nRF54L15-DK v1.0.0) 3.0V operation apps: scan_adv (delete advertising) west build -b nrf54l15dk/nrf54l15...
Hello,
Working on Ubuntu 22.04 with nRF Connect SDK 2.6.1 for the target nrf5340dk_nrf5340_cpuapp_ns (= with TF-M).
My application image became too large. I want to split...
Hi，
ncs v3.2.0，nRF54LM20-DK， I drive a buzzer. When the buzzer doesn't ring, I need a low level. I tried it according to the following method. I can't output a low level...
I need to generate PWM siganl around 4 mhz frequency but i did not get proper pwm signal and i got only millivolt range voltage this issue cuase i did not get proper audio...
Hello, I am developing with nRF5340 with my custom board. I observed a high current consumption when the network core is flashed with the ipc_radio image. I am developing...
Hi,
I am using NCS v3.3.0 and would like to implement the following setup:
Central: nRF52840 Dongle (connected to PC via USB)
Peripheral: nRF52833 acting as...
