Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello Nordic team,
I have a question related to the “nRF5340 Production Programming – Troubleshooting” documentation, specifically the part that says the access port protection...
Per (+) Trouble with nPM1300EK - Nordic Q&A - Nordic DevZone - Nordic DevZone , I've disconnected TWI from the board while doing the battery profiling and that worked successfully...
using the nvs sample from here: https://github.com/nrfconnect/sdk-zephyr/tree/v3.4.99-ncs1-1/samples/subsys/nvs and configured for my board, the program crashes on the 323rd...
It seems to be an assumption in the swi request functions that after req_exit, the swi request should be completed. However, in certain cases, this invariant doesn't hold...
Hi, I tried the above tools(nrfjprog) on the Raspberry Pi 3.
But, I saw the error shown below.
pi@raspberrypi:~$ ls | grep nRF5x
nRF5x-Command-Line-Tools_8_5_0_Linux...
Hi,
I got the nRF5340-DK + 7002-EK running your WiFi Fundamentals HTTP server last weekend. I connected the 5340+7002 to my wifi network and got an IP address. I also opened...
Can the nPM1300 be used without any charging support (no battery, no fuel gauge)?
I know this is an unusual arrangement but we have a requirement that a separate device...
I'm having 52840-DK boards 3 and installed vscode,nrfsdk v2.2.0 and v2.8.0. i want to explore how to use FOTA for zigbee. are there any sample available to make it work and...
Hi Nordic team,
We are planning to use the STM32H747 as the host MCU to control the nRF7002 for Wi-Fi functionality. Based on reference materials and existing use cases...
Similar issue to Attempted to change incrementally the Voltage for VDDIO and VDD_DBGR, however, this didn't change the state of the LEDs. Successfully compiled and flashed...
Hi,
We are seeing weird behavior in the way the nRF Cloud UI displays changes in the device shadow, specifically for properties that are being nulled-out.
Let's say we...
Hi,
Im using an SPI device and also the SPIM NRF driver. This device is not always on, but the overall flow is:
Power On the device on boot and do basic info readings...
I have ordered two boards using the nrf52840
I was able to flash the first board and my firmware is working as expected however whenever I try to program the other one I...
When uploading a network core image though MCUBoot and confirming the image, sometimes it fails to accept and on other builds it accepts the update.
I have narrowed this...
Hi
Greetings, Hope you are doing well.
I am fairly new to using the nRF Connect SDK through VS Code. I completed the nRF Connect SDK Fundamentals course, and I also noticed...
