Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
I have a nRF54L15 firmware built on NCS v3.0.1, with image encryption enabled in mcuboot. Firmware needs to be updated to new version built on NCS 3.3.0.
In NCS 3.0.1, image...
Hi Nordic Support Team,
We are currently developing a product based on the nRF54L05 SoC using nRF Connect SDK (NCS) v3.0.0 . Our application is facing significant Flash...
Hi, is there a sample using nRF7002 on nRF54LM20B SQSPI (or could you share an appropriate devicetree)? I have been successful using the nRF54LM20 DK + nRF7002 EBII combination...
I was looking for more information on Anomaly 244, which states:
Symptoms
Data transfer to and from external Flash with QSPI is corrupted.
Conditions
HF...
Hi, I'm using a WisBlock setup with: • RAK19001 base board • RAK4631 core RAK18030 microphone in IO slot A • RAK15002 microSD in IO slot B I'm running Zephyr / nRF Connect...
Hello.
I am experiencing an issue in Bluetooth Mesh where a Schedule entry that is set to "Inactive" is triggered when the time is updated.
Steps to reproduce:
Register...
Hello,
I work on a zephyr project with the MCUBoot and two updatable images: custom firmware loader + TFM and main application. Update works over BLE. For testing I use...
Hi,
I have an application with custom boards using nRF54L15 (running ncs 2.9.1) as the peripheral and currently a modified nRF9160DK (running ncs 2.5.1) as the central...
Hi
I am using ncs 3.3.1 in visual studio code. I created a custom board in the following location :
D:\hpgsystems\NSOC\nboards\boards\emtecSolutions\ppbr_rev2
The board...
Hi, I am trying to understand the Friend and LPN behaviour. For that I am refering to nRF sample application light" and "light_switch". Below is the setup details: 1. On one...
Hi,
I'm about to develop a custom board with nRF52840 IC. For a first test I need an external antenna. I modified a dongle for a first proof of concept. I removed the antenna...
Hello,
We are trying to assess signal quality while synced to a BIS and we would like to use the RSSI values. RSSI values do show up when scanning and at least in the...
Hi,
I am using two nRF52833 devices with the nRF5 SDK. They are paired and bonded to each other. Occasionally, I encounter the following error in peer_manager_handler :...
I am looking to figure out my current consumption with an NRF52832 chip. I have the NRF chip running at 3V using UART, SAADC, BLE and SPI. The chip is constantly reading some...
I am developing an ESL proof-of-concept based on the Nordic Bluetooth ESL reference architecture and transitioning toward a small-scale PoC production (≈100 tags) . I have...
