I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
starting from ncs 3.2.0 (also in 3.2.1) when i attached the debugger (jlink ultra+, under VS code with nrf connect extension) to my nrf52833 board, i am getting the...
Hello,
We're working implementing a custom board using he nRF54L15 and looking to use the NFC functionality. We have run into an issue that occurs when we try to read the...
Hi, I'm trying to determine whether or not an nRF54L15-DK running Zephyr supports the following relatively recent Bluetooth features and if so, how to enable and use them...
Hi, I'm using v4.0.4 of the standalone Bluetooth Low Energy desktop application to obtain and display GATT details of a connected device. I enable indications on the Service...
One of our employees is following the Cellular Fundamentals courses and they got stuck on getting modem traces out of the Thingy:91X.
In lesson 7 exercise 1, the course...
I have been trying to understand Child Supervision. Part of the documentation that I have read is:
https://openthread.io/guides/build/features/child-supervision
At the...
Hello!
I'm working on a project that was primarily developed with NCS v2.9.0. The application (using an nRF5340) utilizes BLE mesh and is configured to use TinyCrypt for...
Hello,
I am using nRF52833 with nrf connect sdk for vs code (SDK and Toolchain version : 2.9.1).
Hello Nordic Team,
I am using OTA DFU with MCUboot on the nRF Connect...
I have a custom NRF9151 board with Windbond W25Q32JV flash, and some other peripherals connected. It also has GPS and LTE which I have tested and work. My UART console is...
I am trying to flash and use the debugger on a nrf52840 DK to flash a Thingy53, using the ribbon connector as outlined in this video . I tried to follow the steps in this...
nRF9160, SICA B1A, mfw 1.3.7, NCS 3.1.0
I currently try to test the situation, when the battery gets drained "too much" and the voltage drops below 3.0V (e.g. 2.9V) on VDD1...
Hi Nordic Team,
I am using MCUBoot with BLE DFU on nRF5340 and I am facing an issue where the DFU process cannot complete due to my application’s custom boot logic.
After...
My project is running on an nRF52832 with the soft device enabled. At the start of my project I have the following
When I reset the system our normal way (calling nrf_pwr_mgmt_shutdown...
Dear all,
I wanted to modify BTHome template sample for Home Assistant software in order to run enable it to advertise on PHY Coded, there I guess I need to enable extended...
