Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi,
How to implement two sets of SPI on the NCS v3.0.0 nRF54L15 P2 port? If it can be achieved, please provide the corresponding IO ports for these two sets of SPI.
Kind...
Hi，
We are designing a cellular antenna based on the Thingy91x reference, which needs to support all frequency bands of the nRF9151 cellular module. The antenna tuning switch...
Hi Nordic team,
I am using nRF54LM20DK with NCS v3.3.0 and trying to enable QSPI.
However, there is no &qspi or &qspi20 node in DTS, and adding it causes build errors...
Hi Nordic team,
We are designing a custom board using an nRF54L15 together with an nRF7002 WLCSP.
Our board has a single 3.3 V power rail. We would like to confirm the...
Hi,
AI says this is a known issue, but I want a much stronger explanation of why this scenario breaks. I run the server program on the nRF52840. I understand that it is...
Hello!
I am stress-testing the nRF54L15 devkit by sending it random-sized chunks of data over UART at 921600 baud, which the devkit code receives using the asynchronous...
In the absence of a QGAA reference, is there anything to be aware of when designing a QGAA board?
For example, with the nRF52840, the WLCSP and QFN references used different...
Hi Nordic team,
I am working on nRF5340 and trying to enable MCUboot serial recovery DFU in single-slot mode with both signing and encrypted images.
Environment: 1. SoC...
Summary
The Zephyr RRAM driver drivers/flash/soc_flash_nrf_rram.c does not pass NS-side reads of TF-M secure flash through soc_secure_mem_read when the device tree uses...
I am interfacing a TLV320AIC3204 codec EVM with an nRF54L15 board using I2S.
The codec EVM default configuration is working correctly. I verified audio on the EVM side....
Bluetooth physical layer Direct Test Mode testing is used to verify BLE low-level RF transceiver performance. The required software is nRF Connect for Desktop V3.7 + Direct...
Hi,
When starting nRF Connect for VS Code, SDK v3.3.0, the message Unable to resolve configuration with compilerPath: "C:\ncs\toolchains\fd21892d0f\opt\zephyr-sdk\arm-zephyr...
Hi,
We have two option to use Flash memory,
Option 1: We are planning to use Flash Memory on the SPI bus shared with the NRF7002. Kindly confirm whether this configuration...
Hello Nordic Team,
We are trying to test an I2S DAC (MAX98357A) with the nRF54LM20B EVK . Could you confirm if this is supported and which sample application is recommended...
