I have an NRF9160 system running and I see mention of " The nRF9160 PWM peripheral can capture the period and pulse width of an external PWM signal" but was a little confused...
Hello, I am encountering an issue while setting up an OpenThread Border Router (OTBR) using the following hardware: nRF52833 board (flashed with RCP firmware) nRF52840 board...
Hi
custom board using the nRF9160, toolchain version v2.6.0, mfw_v1.3.6.
Sorry I can't provide a decrypted modem trace, but I hope the screenshots are enough to show what...
Hi, I am working with nRF52 DK (52832), and the issue I am facing is that i am unable to increase the data size of data SPI -DMA can receive. Currently it is configured at...
Hello everyone,
I want to evaluate the power consumption in idle mode of the nrf9151 sip.
Environement:
nrf9151dk_rf9151_ns
nRF Connect SDK Toolchain v3.0.2
VScode...
I’m using SMP over UART to send the erase command ( {"slot": 1} ), and it only erases the application core image (image 0). I also have a network core image (image 1) present...
So i am currently referring this ticket and from that I get to know that when when setting parameters for create config (HCI_LE_CS_Create_Config) command for channel sounding...
Is there a bootloader for the S130 available already? It seems to be not completely trivial to adapt the S110 bootloader to a S130 bootloader...
In the SDK, two bootloaders...
Hello everybody,
I try to work with BLE Devices using LabView and the MasterEmulator API. I can start the USB Dongel (PAC10000) and enable "StartDeviceDiscovery". The Property...
Just starting out with the nRF51822-EK here and we wanted to try out the Gazell protocol. Any ideas on how we get the firmware we need to do that? Thanks.
Hi,
I am using nRF 511822.I have edited the sample code ble_app_uart and tried to interface the button interrupt handler.But the interrupt is not triggering. I have added...
2 arduino nodes with nRF24L01+ transceivers. Using maniacbug's RF24 library. Using pipes 0 and 1.
When I set Auto-ACK ON for all pipes rf24.setAutoAck(true) : it works...
Hi,
I am using nRF51822. I need to create a timer interrupt handler, which can trigger at 1us (microsecond). I am using Keil. Now i am using the 1 ms (microsecond) timer...
i am absolute newbie, hope i can find some help and guidance here.
i am looking sample program to send a text string from nRF24LE1 to nRF24L01+ (just 10 characters). actually...
Hello,
I am not much of a PCB designer but want to tinker with nrf51422 EK Altium designer files provided. I try to open the project file using Altium designer 14, but...
Hi all,
I am new to hardware design and would greatly appreciate pointers. We intend to use mini-USB port for charging/power supply rather than for data. What is the best...
Hi all,
I am using NRF24LE1 32pin.
Does anybody know can I apply on XC1 pin external frequency different from 16MHz if I am not using radio module??? Thanks.
I am currently using the nRF51422 DK along with the nRFgo Starter Kit. I followed the instructions in the PDF "nRF51422_DK_UG_v2.0," and I attached the nRF51422 with PCB antenna...
use keil to download code to flash fail
use nRFgo studio to connect target device error
Load
C:\Keil\ARM\Device\Nordic\nrf51822_v5.0.0.34603_Backup\Board\pca10001...
Hello,
when using Keil's ULINK Pro debugger V1.57 connected to PCA10006 board for debugging nRF51822 code the ULINK is recognized by µVision V5.1.0.0 but the FW download...
I have an nRF51822 (256KB) that I want to program with some data targeted at 0x20000 to just under 0x38000. My code starts at 0x16000 (allowing for S110) and is only 1700...
I have a nrfgo 6310 start kit that I use for my nrf51822, but I'm wondering if I can also use the nrfgo 6310 for the nrf24Lu1 development kit as well? I tried plugging in...
