The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
When the USB stack and your local Filesystem code both try to control the flash chip simultaneously, the system will crash or trigger a HardFault, causing the restart.
Dear Nordic,
I have a few questions I would like to ask.
1. I would like to inquire if there is an antenna pattern for the nRF54L15DK PCB.
I have already searched through...
I was trying to flash a program on nRF52833 development kit and got this error, it important to notice that my college was trying to flash (via VS code) it before and I am...
Hi,
I'm working with the nRF54LM20 DK (nRF54LM20A) and evaluating whether it can act as a USB host to read data from an external USB CDC ACM device.
The intended setup...
Hi
I remember the Devzonw could ask for hardware instructions. My matching circuir has used the nRF54L15 reference design and nRF21540 DK design, all the value is the same...
I used binwalk to analyze the zephyr.signed.encrypted.bin file generated by the routine mcuboot_with_encryption. I found that the firmware was not encrypted but merely compressed...
We have a peripheral device that maintains a PAwR sync (as a syncer/responder), connects to another peripheral in a central role, and also accepts connections from a central...
I tried writing read and write code for sEMMC based on information obtained from an AI assistant. The resulting code is shown below:
As you can see, the block address...
I used an oscilloscope to check the waveform and found that only the clock and IO0 had waveforms. I am using this interface to send data:
nrfx_err_t nrfx_qspi_write (...
This is just simple feedback on the nRF Connect Toolchain Manager v0.9.2.
The download speeds when installing an SDK are terribly slow. On a 1Gb /s connection my PC was...
Hi Nordic team,
We are currently migrating our project from nRF Connect SDK v3.1.1 to v3.2.4 on the nRF9160 .
Our application was working without issues on v3.1.1. After...
I am working with:
NCS Version: 2.6.1 (SoftDevice Controller)
Hardware: nRF52x Platform
on a custom board (nRF52 series) and I'm trying to achieve a "Headphones...
Good morning,
It has been implemented a sleep mode to save battery when the board is not used.
To do that we follow the documentation and implemented the SystemOn mode...
Dear:
I am using SDK12.3 with S132 write application using BLE+DFU+UART+I2C, The device connects and communicates with mobile devices through our own application(ONF Link...
