Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hello Nordic Team I Have tried different usb cables ,and different PC .
all cannot connect to the software .
can you help me to check what has happened .
open log...
I am on the learning curve of nRF9151 and LTE/GNSS.
Trying to build and run the sample app under nrf/samples/nrf9160/location
The errors Im getting are
[00:11:23.476...
Hi, I have upgraded my custom nRF52840 devices from SDK 2.4.1 to SDK 3.0.2. For few days, these devices did connect to existing OpenThread network. But now, all SDK3.0.2 devices...
I used the Bluetooth mesh distributor example from ncs2.9.1, and the Bluetooth mesh dfu can proceed normally. However, when I tried to pause and resume the dfu process, I...
Dear Nordic Support Team,
nPM2100, SHPHLD pin: we would like to connect a pushbutton to GND to wake the PMIC from ship mode. Additionally, we would like to read the pushbutton...
Hello, I am currently designing a custom board using the nRF9151 and I have a question regarding the SWD interface. My understanding is that the nRF9151 contains two main...
We're using the nPM1300 in our designs and we noticed that the charge portion does not appear to keep a battery charged when USB is connected for extended periods.
Our arrangement...
So far we have been using nRF5 SDK v17.1, but we ended up using nRF connect SDK v1.9.1.
However, this compiles too slowly.
I modified main.c and it seems to compile everything...
Hi,
I’m using NCS v3.1.0 and noticed that my application does not run unless I enable:
CONFIG_CLOCK_CONTROL_NRF_K32SRC_RC=y
Without this configuration, the system fails...
HI TEAM,
I am using a custom board and measuring its overall current consumption using the NRF Power Profiler Kit 2 (PPK2) .
Setup details:
Power source: External...
Hi,
We are using the nrf9151 to get GNSS data/coordinates without using A-GNSS, we followed the information in the following page "https://docs.nordicsemi.com/bundle/ncs...
Hello Nordic Support Team,
We are currently developing an IoT product using the nRF9151. In our application, the device wakes up once per day, transmits a small amount of...
