Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi,
I am facing issue on nRF54l15 MCU where after uploading the image from the devcie manager app, I don't see image getting swapped from slot 1 to slot 1. FYI I am storing...
We are using nRF52832 with NCS(v2.9.2)/Zephyr and the watchdog (20 s timeout). When the application enters System OFF (e.g. after idle), the device goes to sleep but then...
Hi,
I have just bought a PPK2 and (mistakenly on my part) assumed it must read the Voltage of the output as well (necessary for power measurements). I see now that it doesn...
For a very small percentage of our devices, we sometimes see watchdog reset events that we cannot explain. The only pattern that we see so far is that the watchdog reset happens...
I am currently developing a project using an nRF5340DK and a custom board.
For some unknown reason, the device is being identified as an "Unknown device." The ironic part...
uart_nrfx_uarte.c, uarte_pm_suspend checks some preconditions with __ASSERT_NO_MSG. In my experience that causes unintended and not required crashes. If the precondition is...
I am building my custom PCB with the nRF52840 chip using the Fanstel BT840F SoC. I have designed and fabricated my own PCB. I am able to flash the code onto the SoC only once...
Hello,
While using ai.lab.nordicsemi.com for model training, I noticed that after the training process is completed, the platform generates several performance charts, such...
Hi,
In my board design, I'm planning to use nPM1300 to power nRF5340 and nRF7002; the user has the option to connect or not connect a battery. If I programme the current...
Hi,
We're developing BLE products with the software developed on nRF SDK v3.2.2.
We are affected by the known issue of the SDK: NCSDK-32763: Upgrading firmware may corrupt...
nrf 5sdk + s140 + 52833 I'm currently debugging the time-sharing operation feature for BLE and the private protocol. I've found that after I power on and initialize the SoftDevice...
Hello,
We currently have various products built around the nRF52810 and the nRF52832. We almost always use a PCB antenna very similar to the one on the "nRF52840 Dongle...
Hi, I am working on project to obtain ecg data via bluetooth. But before that I was trying to see whether I could obtain ECG signals serially through nrf52833. And I tried...
Using nrf5340 with nrf70 on a custom board.
I want to use the wifi interface to send raw wifi network packets (both in associated and non-associated modes).
I have the...
