Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Starting with the lbs example from lesson l4e2 of BT fundamentals course, I'd like to send an indication similar to the button (and keep the button). I basically created duplicates...
I am using the nRF9151-DK with the standard (from code examples) firmware . When configuring both P0.13 and P0.17 as ADC inputs, I notice that the current consumption on P0...
I am working with the connected_cs examples on the nRF54L15 DK and trying to swap the GAP roles. In my case:
Initiator = GAP Peripheral
Reflector = GAP Central...
I am working on a Bluetooth Low Energy (BLE) project using the nRF52840 Development Kit (DK) , which has been reconfigured to simulate an nRF52805 chip. The firmware is based...
How can you get the simple channel sounding test going with the bluetooth/cs shell commands?
I've got the shell working over UART and devices talking with each other but...
I tried to add external memory to mcuboot. In fact, I have successfully added it in app, but the same configuration seems to have problems in mcuboot ，mcuboot reports an error...
Hi,
We are developing a hardware and software solution for a locator tag using a minimalist approach. We want to use both, the Google Find Hub and Apple Find My Network...
I maintain an nRF52840 project on the legacy nRF5 SDK and am migrating to an nRF54L15 Bare Metal project.
I could not find a bare-metal “radio test” example, so I’m bootstrapping...
I do connect 52840 DK board to PC through USB cable, sine I want to see runtime log. but meanwhile, I want to use PPK2 to see the current of 52840 DK board, Can I get the...
Hi everyone, I noticed something unusual while testing BLE transmission and reception:
Transmitter: nRF5340DK
Receiver setups tested:
config：Target board...
Hi,
If I build the extxip_smp_svr sample app for the nrf5340dk board. The network image firmware version is set to 0.0.0.0.
To reproduce the issue, do the following...
In Lesson-3 Ex-2 for the BLE Fundamentals course, the steps for setting preferred PHY (steps 7 thru 9) is causing fault on my nRF52840-DK board.
Log messages are as follows...
Hi Nordic Team,
I'm currently working on integrating TagoIO using MQTT in our application. While attempting to add the MQTT connection details—specifically the username...
Hello,
I have a problem with a custom board using a nRF9151.
I can flash the nRF9151 and it seams to flash successfully (I tried with a blinky program and the leds start...
Hello, I am experiencing issues with the current measurements taken by the PPK2 when using the nPM2100-EK to power a device. The current drawn from the 2.7V power source ...
