I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hi my ffriends,
I’m working on a wireless system called for me " Wireless Link Project" , based on the nRF24L01 (non-Plus) transceiver.
I have two identical boards using...
Hello DevZone,
I have a confusing question about TF-M. Need help from a TF-M expert.
In this document , it says that we must disable uart1 in non-secure application, because...
I'm trying to test the overall pwoer consumption of my setup (nPM1034EK and nRF54l15DK) using the PPK2. As I've started this, I've gotten far higher numbers that I expected...
After I reset the kit (custom equivalent to nRF52DK) it advertises, and I can connect from the BLE Standalone App on my Windows computer. But it only advertises for a short...
I recently bought a fanstel blg840 device, and I have programmed At client firmware in nrf91 and custom code into nrf52, but the problem is nrf52 is sending at comments to...
I am trying to work with my flash deivce in my code. for some reason:
const static struct device * int_flash_dev = DEVICE_DT_GET ( DT_CHOSEN (zephyr_flash)); doesnt work...
I have been having a series of issues with programming from nRF Connect using a J-Link programmer. I have made a couple of other recent posts and in each of those, I thought...
hi,all
I used to use nrf54l15dk board as a client server, want to connect to a bluetooth remote,and get bluetooth remote notify message;
I use sample "central_hids...
Hi guys,
I have MQTT v5 up and running but I am currently trying to implement one-way TLS then mutual TLS once it's completed. I am not too sure what I am doing wrong but...
Hi:
My environment is: Windows laptop, nRF52 DK (Peripheral), nRF52840 Dongle, Mobile Central (iOS and Android), and Wireshark nRF Sniffer for Bluetooth.
Peripheral sends...
Hello all,
I have problem with flashing the code. It gives me memory protection error.
Steps I followed for creating firmware and flashing:
1- I took a sample from nrf...
I'm working on a product prototype using the nrf5340 audio dk to send audio via Auracast. We started from the nrf5340_audio application, as it implements a large fraction...
While testing UART communication between a Seeed XIAO board and the nRF9151 DK, I connected the following pins: - XIAO 3.3 V → DK VDD - XIAO GND → DK GND - XIAO TX → DK RX...
Hello,
In the nRF52840 datasheet, some pins are explicitly marked as “low frequency I/O only.” However, I couldn’t find any similar indication in the nRF54L10 datasheet...
