Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hi everybody, I have some problems with flashing my custom PCB with an nRF52832. I saw online that you can flash the nRF52832 using the nRF52840 DK. I have looked into a lot...
Dear Support Team, I have downloaded the latest version of VS Code;
I have also installed the latest version of the nRF Connect for VS Code Extension Pack;
The J-Link...
ncs: v3.2.0
chip: nRF54L15
If I set CONFIG_PM_PARTITION_SIZE_MCUBOOT=0x10000 (64K), MCUboot fails to boot, and the error displayed is: 'Protect mcuboot flash failed...
We are not using the NRF5340DK board. According to tests, after initiating an SPI data exchange, the program is delayed in executing the next CS pull-high operation, resulting...
Hi,
I’m trying to finish the first exercise of lesson 1, but when I save it to flash and run the binary, I get this error and I don’t know what’s causing it.
Could someone...
Hello dear community!
Few months ago I bought a NRF52840 from MakerDiary ( https://wiki.makerdiary.com/nrf52840-mdk-usb-dongle/ ) for a personal project arounf Zigbee...
Hi Team,
I am using NCS v2.9.0 and trying to implement a custom Zigbee cluster with custom attributes.
Could you please suggest an example or guide me on how to send...
I'm currently testing the walkie-talkie mode on this development kit, however, when testing it outdoors it only allows a very short connection distance and disconnects. How...
Hi, this question might sound a little silly, but is downloading my device location history from nRF Cloud free of charges? I want to analyze my device's travelling pattern...
Hi there,
I am using an nRF9160DK and looking to get accurate Timing Advance numbers from it and also information on neighbouring cells. I believe in order to get an accurate...
We are using both serial ports running over USB on the nRF54L15DK:
uart20 is LOG, CONSOLE, etc.
uart30 is for our communication (enabled in our overlay)
When we...
Hello,
I am trying to get a custom board working with NOR Flash chip but I am having issues getting the flash chip "ready". I am running the sample application "spi-flash...
Hi!
I've used nrfutil to dfu ble before on a target that just loads and runs a bootloader (for cycle testing).
I'm trying to use it again with a target in the application...
We have a NCS 3.0.2 app + MCU boot with OTA functionality on nRF54L15 (PCA10156 rev 0.9.3)
After upgrading to NCS 3.1.1 it doesn't boot anymore.
I tried with
Key provisioning...
nRF9151 has access port protection enabled by default. I need to debug firmware for nRF9151 produced by a non-secure build. I am trying to follow Figure 120 (Access port unlocking...
