I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
I measured the impedance using a VNA on the J1 socket of the nRF54L15-DK RF: With the RF configured for receive at 78.6 + J7.8, RF transmit continuous carrier at -40dBm: 23...
Hi Nordic support:
Our product used nRF9151 modem. During production, we encountered an issue with approximately 0.1% probability on the nRF9151: It's firmware lost or corruption...
I used the timeslot function of the nrf52832, but when I called the radio to send data, I found that the signal strength was very weak, much lower than that of BLE. This resulted...
I am using nRF9160 DK with nRF Connect SDK v2.9 and the LwM2M client sample ( /samples/cellular/lwm2m_client/ ) , converted from PSK to X.509 certificates .
The device connects...
In the software development for the nRF52832, the SEGGER_RTT_printf() function is called throughout the code for debugging and problem analysis.
Would there be any particular...
Can I copy the ESB code from SDK v3.3.0-preview3 into SDK v2.9.0, and then get the functionality in esb_ptx_ble & esb_prx_ble?
Is there any way to achieve it quickly?
Hi,
I am working on a project with two nRF52840 devices (nRF Connect SDK 3.2.4 / Zephyr RTOS) that are already connected via BLE. On top of the BLE link I need a low-latency...
Hello,
I need to measure current consumption on the nRF52805 in sleep, TX, and RX modes. Which sample applications are recommended for each of these measurements? Additionally...
Hello,
I am facing issue in reading the eDRX mode configurations using AT Commands on nRF9160. Below are the details of hardware & modem fw version.
1. Modem FW version...
What is the recommended way to clear the retained LATCH register using the zephyr generic GPIO functions after waking on interrupt from system OFF? It does not appear to be...
I have designed a custom PCB using nRF54L15 SoC and have gotten it verified from Nordic people. I will share the gerber here as well. I am using VS Code for flashing the code...
# Console disabled - uart30 used exclusively for MCUmgr SMP
CONFIG_SERIAL = y
CONFIG_CONSOLE = y
CONFIG_UART_CONSOLE = y
CONFIG_PRINTK = y
CONFIG_LOG = y
CONFIG_MAIN_STACK_SIZE...
Hi everyone i have a problem with building a project, i dont know what i did wrong, before everything was building fine, but now if i pristine build any project some lines...
Hello,
My application crashes with a Kernel Panic (ZEPHYR FATAL ERROR 4) during NFC communication :
ASSERTION FAIL [ header.ctx_size <= 16 ] @ WEST_TOPDIR/nrf/subsys...
Hello this is my first time designing nrf series. and i want some feedback of my board design and rf circuit
Thanks in advance for your time and suggestions.
these are...
