Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Trying to migrate from SDK v2.7.0 to v2.8.0 and suddenly getting the build error
Based on other forum posts, I was able to track down more information using the <build target...
Hi, I just got two nRF52840 dongle and it works great as BLE sniffer.
I want to send continuous BLE data (not only advertising) packet and sniff packets between bonded devices...
Dear Nordic Team,
I am currently working with the nRF5340 DK and would like to know whether it is possible to read or retrieve the Network Core firmware version directly...
Hi,
I am using NCS 3.2.1 and nRF52840-DK's version 3.0.3.
I flashed 2 boards with the openthread/cli sample.
From the CLI on both boards, I issued the following commands...
I’m trying to transmit a payload of up to 2,450 bytes using CoAP over OpenThread. Before jumping into firmware development, I want to evaluate the feasibility of transmitting...
Hello DevZone,
I have some questions about nPM1300. I know that nPM1300 need a battery pack that already contains a PCM.
When the PCM activate the protection due to overdischarge...
Hi,
I'm using the nRF54L15 (custom board, nRF54L15 DK base) with NCS v3.1.0.
I have two UARTs:
uart30 — Shell/console (needs CONFIG_SHELL_BACKEND_SERIAL=y , which...
Hi,
I'm trying to use an nRF5340 Audio DK to communicate with another board via SPI. The voltage needs to be 1.8v. How do I configure my board to do this?
Hi,
We are using the nRF7002-DK board. I am using Zephyr samples/net/wifi/shell with no other external connection other than the j2 micro-usb connection to PC and with the...
Hi,
We're aware of the modem 2K TLS buffer limitation. It's causing us quite a bit of headache related to the device shadow.
Our application needs a number of config parameters...
Hello,
I am trying to access to two partitions of 2gb each on a micro SD card of 32gb.
I can access to one partition of 32gb in my micro sd card but as it is formatted...
I've been struggling with Thread connectivity on a custom PCB, powered by a MinewSemi ME54BS03 module (with IPEX connector)
I'm using an external 2.4GHz antenna and I'm...
Hi,
I am facing a power consumption issue with the nRF54L15 (BM15C SoC) in deep sleep (System OFF / low-power state). The measured current consumption is approximately 221...
Hi all,
Note that I am using a Fedora Workstation VM on VirtualBox for keeping everything clean. I pass the connected USB development board to the VM. I am trying to evaluate...
