Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hey, I was trying to look for information on how nrf9160 modem selects the network to use, since we are having slight trouble with some devices triggering full network re...
Hi,
I am testing the radio_test (short-range) sample on an nRF54LM20A DK . The test setup is:
Board: nRF54LM20A DK
Sample: peripheral/radio_test (NCS version...
Hi all,
I'm working with building/programming v3.1.1 SLM application for my nRF-9151, it all goes well while testing with nRF-9151DK.
But when I want to try my custom...
Dear Nordic Team and Distributors,
For nRF54L15 (CSP and QFN) design circuits, how to optimize the stable modulation issue?
What aspects should we consider to do failure...
Hello Nordic team,
We are evaluating nRF54L10 for a battery-powered Bluetooth LE medical device .
We are considering the nRF Connect SDK Bare Metal option instead of Zephyr...
Hello! We are in the middle of an upgrade to 3.2.1, and we encounter the following issue using SB_CONFIG_MCUBOOT_MODE_SWAP_WITHOUT_SCRATCH, SB_CONFIG_MCUBOOT_MODE_SWAP_USING_MOVE...
Greetings,
I'm considering nRF52840 for a product. My connectivity requirements are BLE 5+ (For GATT-based communication, No requirement for channel sounding, etc), USB...
Hi,
working on custom bootloader on nRF52840 with S140 v7.2.0(not enabled in bootloader) with SDK.
This is code for erase and write:
Now, when writing I get prints...
Hi there! I am trying to set up external flash (w25q64) with my NRF52840 project over SPI. I have adapted the spi_flash sample in an attempt to set up this device, but I am...
Hi,
nRF9151 + Kyocera AVX P822601 internal SMT antenna: 8 dB RSRP loss vs external antenna — possible PCB layout issue?
Test Results
Test 1 — Out of Faraday cage, internal...
Hi everyone,
We recently started to add the iBeacon broadcasting to our own BLE project that runs on an nRF5340. It is based on the code from the sample of the SDK (we currently...
Saw this post from about 1 year ago.
Any updates regarding USB host firmware support on the nRF54LM20 or any timeline for when it is expected to gain some level of support...
Hello, I wanted to update my project (Custom board using the nRF54L15 ) to the v3.3.0 SDK since this fixed a BLE bug with the v3.0.1. version. To my knowledge I did not change...
Hello,
First of all, I'm delighted to have found the beginning of eMMC support for Nordic devices as software peripherals in NCS 3.2.0: https://docs.nordicsemi.com/bundle...
