I have used your example of a bootloader nAN_18. I can create a basic program, with new firmware, and also load my new bootloader program at the high end of memory.
My...
Hi,
I'm developing some projects with the nRF51822 chip and I am not able to debug them successfully any more. However, I have previously debugged correctly some projects...
Hi,
We've been seeing an intermittent connectivity issue in Yosemite in discovering BLE services, namely scanForPeripheralsWithServices does not return anything. The same...
Hi there is a problem in github.com/.../nrf51-UART-examples
any one can help?
I put empty loop in main, and comment off all ble related int. and I process uart_evt by...
Hi,everybody！
When i install master control panel 3.10.0.14, i can't find nrf.exe in " C:\Program Files\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf ". Only nrfutil...
Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
Hi --
We are in the process of setting up to flash a few hundred devices for our internal testing. We can currently flash to our board using nrfjprog either directly from...
I have a eval setup where I use the nrf52840 dongle with hci_usb flashed. It has a non-default config to enable DLE (this works fine).
I am sending buffers of 8192 bytes...
Hello,
I'm looking to get XInput working on the nRF52840 so that our device can appear as an Xbox-compatible game controller. I'd appreciate any guidance or recommendations...
Hi,
I have an application which is developed using nRF5 SDK version 17.1.0
Migrating to nRFConnect SDK is not an option at this stage of the project.
The application...
I'm stuck trying to set my nRF Connect extension on VSC. I've followed the guide for the installation but I'm reaching a wall. Every time I try to install a given SDK I have...
Hi all,
I am currently testing on nrf52dk (PCA10040, 3.0.0) with NCS v3.3. Note: I also tested with vanilla Zephyr and see the same issue.
The code I run is to 100% the...
Hello,
I previously opened a ticket describing an issue where using MCUBoot in NCS v3.1.0 caused the GRTC to reset after a sys_poweroff() .
As discussed in that ticket...
Hi everyone,
I'm evaluating the nRF54L15 for a very low-power sensor node application powered by a Lithium Thionyl Chloride (Li-SOCl₂) primary cell. The goal is to achieve...
Device : wearable IOT device
Battery capacity : Max 4.2V (Typ. 3.7V)
BLE Tx Power : Tx power is highest when the battery capacity is 4.2V (measured in air, not conduction...
Hi, We want to use Sensibel microphones in a project with nfr9151, and it will be used to sample one microphone (mono) with 24bit data. This microphone seems to require 32...
Hello, Nordic Support!
I have some problems with programming my custom boards using my nRF54L15dk v0.9.1, when I use a setup with long cables (or several cables & adapters...
Hi all! I need to see the printks and log messages from the b0n and cpunet app in RTT Viewer. The problem is, whenever I connect with the SEGGER RTT Viewer to the netcore...
Good morning,
we are using the Zigbee stack (ZBOSS) on nRF52 devices with Green Power Sink enabled and we are integrating a Green Power door sensor.
nRF5_SDK_for_Thread_and_Zigbee_v4...
Hi guys,
I'm hitting an error with the current Aliro 1.0.0 lib.
When a credential is signed today but its validFrom is in the future (e.g. signed=2026-06-17, validFrom...
I am doing some development on nRF5340 and I experienced MPU faults. We tracked down the root cause and this led to a PR https://github.com/zephyrproject-rtos/zephyr/pull...
