How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
nrf5340 NCS 3.1.0
Hello, I am trying to improve boot time and here are some spikes and timings. What I have found out is that CryptoCell init (hw_cc3xx_init_internal) takes...
Dear Nordic Team,
I'm currently working on an application that uses ACL and ISO to transmit data between 2 devices. ACL is used for transmitting operations that are then...
Hello,
I am developing using nrf5340 and optimizing the Bluetooth throughput currently.
Although experiments go well, there are a few things I would like to know more...
Recently, I've been evaluating the I2S interface of the 52840 to read ADC data from the TLV320ADC6140 chip.
The TLV320ADC6140 datasheet states that the chip supports TDM...
Hello everyone,
I’m a student currently working on a university project related to BLE-based positioning using the nRF54L15 and Channel Sounding .
In the documentation...
Zephyr board: nrf54l15dk_nrf54l15_cpuapp
Hi, we have a custom SPI NAND flash driver and are trying to create an external flash partition for our littlefs file system.
...
I'm very new to Zephyr so please be patient with me. I'm looking for an example that show me UARTs running on the following pins and setup. I have the echo_bot working with...
Hi
There is a github repo https://github.com/nrfconnect/Asset-Tracker-Template/tree/main that receives updates as of yesterday.
However on the documentation website...
I'm trying to get a previously fully functioning MQTT connection back up and running after some hardware difficulties, but am failing to get it to connect to the MQTT broker...
Looking for an example to adapt into my program.
I detect 'smp_svr' but compiling it give me error, it seems I need a flash configuration in file pm_static.yml, but I have...
Dear Nordic Support Team,
We are currently developing a new product utilizing the nRF9160 LTE-M module.
We are in the process of acquiring CE certification for our end...
Hi,
I have been facing issues with the configuration of the nRF9151 for sending and receiving UDP packets via the Skylo NTN network.
I am running firmware version:
...
Hello, on my nrf54l10 I observed a pin (GPIO 1.03) being actively driven low for ~20 ms during a reboot (e.g. Resetting after SystemOff Mode). I need this pin to stay high...
[5/10] Performing build step for 'peripheral_lbs' ninja: error: '/index', needed by 'zephyr/include/generated/ncs_commit.h', missing and no known rule to make it
FAILED...
Since a while back ( github.com/.../999b6a14a4556f16d2f535207a84ceb2cca54f8a) the west flash command with --erase was changed so that --erase would also erase external flash...
