Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
I've been living with this for a while now, but it's getting annoying very quickly. I have a project in VS Code that uses the nRF Connect extension to build for nRF52832 and...
Hi
I want to use the FEM 21540 with nRF54LM20.
My overlay is :
My config is:
I think this should work because my nRF54L15 DK works well with this.
But it is...
Hello everyone,
I’m currently porting my old projects from NCS version 2.9.0 to 3.3.0.
In doing so, I no longer want to use the outdated Partition Manager; instead, I...
Hello. I used the "peripheral_nus" example for nrf52840 - everything goes as it should - I connect via bluetooth and the "nrfConnect - mobile" application receives the message...
Hi Team,
I am working on an nRF52811-based BLE application using nRF Connect SDK (Zephyr) and facing an issue while trying to store the device name in flash using the Settings...
Hello Nordic Support,
I am currently re-qualifying our Bluetooth product in Bluetooth SIG Launch Studio because we had to migrate from NCS SDK 2.1.4 to 2.9.2 due to a security...
Hello, I know this is not the best place for this question, but I did not find any other way. How can I delete my profile from your website including all related data?
Kind...
nRF54LM20A:
C pin is the pin input capacitance on pins XC1 and XC2 .
Could you provide the typical, maximum, and minimum values of Cpin?
This information is needed...
Hi Nordic team,
I have a question regarding the RF matching networks used in the nRF54LM20A-PAAA reference design and in the nRF7002 Expansion Board II (PCA63571).
For...
Hi team,
We are going to kickoff a new project of 2-mic AI recording pen. Good to see we got a very high performance for 54LM20B with DSP/NPU, which might be a very good...
Hello. I am a beginner and I have a nrf52840 Dongle board. I tried to use the interrupt from TIMER0. I defined the timer and it works correctly, but when I enable the interrupt...
I'm trying to flash a u-blox NINA-B406 (nRF52833) using an ST-LINK V2 that has been converted to a J-Link using SEGGER's STLinkReflash firmware. When I select the correct...
Dear Everyone, We're using the PAN B611 evaluation board (ENW89861AXKF) which features a PAN B611-1C Bluetooth Low Energy (LE) module which is based on the Nordic Semiconductor...
