An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hello Nordic Forum,
I ran the Power Profiler Kit on an nRF52DK development board to establish a baseline power consumption.
The current firmware project is quite simple...
Hi,
I am developing a low power BLE device using Promicro nRF52840 boards. After updating to ncs3.2.1 I have noticed a high power consumption in sleep, that isn't present...
Hi! I'm running into a strange issue.
I have inherited this project and it is poorly commented. I have 2 peripherals and 1 central. The 2 peripherals are identical devices...
I am developing a product which uses one nRF5340 Timer in timer mode and another in Counter mode. Reading through the nRF5340 Product Specification v1.6 I have the following...
Hello Support Team,
I am currently working on Channel Sounding with the nRF54L15 devkit, and I am encountering an issue when using main_mode .
Until now, I was using the...
After defining the ADAPTER and initializing UART2 the The adapter pointer fails a test on line 287. FATAL: async_adapter_uart2 points to Flash (0x246d4). Linker Error. This...
Hi, I've tried signing up for a SUPL licence a couple of times but it keeps getting denied. Not sure why. I have logged into devzone.nordicsemi.com and am using the same email...
I’m trying to read/write data to the internal flash of my nRF54L15 SoC using the NVS (Non-Volatile Storage) library.
I successfully flashed the sample nvs application on...
I try to write data into the OTP section of the APP core with the following command line:
nrfjprog.exe -f nrf53 --program 'OTP.ihex'
ouput:
[error] [SeggerBackend] ...
I am trying to program MS12SF1 module through nrf5340DK. I tested the blinky code to toggle the LED pins but while checking through oscilloscope the pins showed nothing, wasn...
nRF54l10 on our custom board in system off has high current consumption, approx 98 uA.
Utilizing the system_off code (C:\ncs\v3.0.2\zephyr\samples\boards\nordic\system_off...
I have got to start with nRF7002-dk and the Wi-Fi sample from the quick start is not working.
I have tried to compile the code on VS code and flash the same code on the...
I would like to estimate the current consumption when the controller is advertising at 2.3Seconds, using external crystal, Tx power of 8dBm, Tx payload of 31 bytes. When I...
We are facing in BLE connection issue in Android phone.
we are planning to use 1. Android phone with 'nRF Connect' for mobile as BLE central. 2. Long range demo applictaion...
Hello.
I am currently testing nRF Cloud and encountering an issue.
I have flashed the Peripheral Memfault Diagnostic Service (MDS) sample program to an nRF54L15DK and...
