Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hello,
I am building my own board with the nRF9151. I see that it can do SPI, but it does not say what pins are SPI capable. As the chip is a SoC (or CiP), can I use any...
Looking at the datasheet for the nrf54h20 it lists GPIO port P9 as Slow and Analog.
However, in the pin mapping, it also says SPIM130 and SPIM131 are available on port...
Hello,
We are trying to run 802.15.4 alongside our BLE Mesh network on the nRF54L15.
However whenever compiling with CONFIG_NRF_802154_RADIO_DRIVER =y, we run into the...
Our peripheral medical product, based on the nRF5340, is designed to pair and bond with both PC and mobile devices via Bluetooth Low Energy (BLE).
I've implemented BLE Security...
Hi,
I'm developing a custom MBR/bootloader for NRF52811 which is used as a second/radio MCU on the board. The MCU will need to run applications with and without the softdevice...
Hello,
I see that the nRF54L15 recently had a datasheet released at v1.0. Is there any difference between this and the preliminary v0.9 datasheet? I cannot seem to find...
Hi,
SDK 3.0.2, nrf9160 (actinius icarus som), custom board, based on modules example. LTE-M with PSM.
Floor current is too high, at around 500 uA. There is a known issue...
Hi,
I am looking to create use a pm_static.yml to create a partition table for MCUBoot, which have the internal flash as the primary boot partition and the external SPI...
I get this error after creating a custom board
C:/ncs/v3.1.0/nrf/subsys/mpsl/init/mpsl_init.c: In function 'm_config_clock_source_get': C:/ncs/v3.1.0/nrf/subsys/mpsl/init...
I'm attempting to put together an application using the baremetal version of NCS just released... I need these to run DFU over BLE so we can update in the field.
I created...
Hello,
I am experiencing a recurring issue when programming multiple nRF52840 boards using the nRF Programmer.
Problem description: When programming the first board...
Hello, I have a pin that controls the power flow to the sensors on my board. it is active low, when it gets a raw value of 0, it allows the power flow to the sensors. I have...
I have just upgraded my project to NCS 3.1.0 and I'm now getting this error
BOOT_SWAP_USING_MOVE (defined at C:/ncs/v3.1.0/bootloader/mcuboot/boot/zephyr/Kconfig:575) set...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
