I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
Hello,
Currently working with NCS v3.10 and using SMP service with external flash to store image in a custom board. I'm capable of upload zipped application using DFU button...
I am using the nRF9151 DK, using the Serial LTE Modem firmware from the nRF Connect quick start.
I am planning to use nRF9151 as a serial modem, and connect it to my Host...
Hello
I was attempting to update a pre-production project where we have 2 servers connected to one gateway where the servers send the audio data back to the gateway with...
Hey guys, I want to store sensor data as circular buffer in non volatile memory. I saw https://docs.nordicsemi.com/bundle/zephyr-apis-latest/page/group_file_system_storage...
If a heartbeat or other chunk reliant on symbol file data is ingested when there is no symbol file associated with the Software Version / buildID it seems like the chunk is...
Hello,
I am currently trying to make an application that can do FOTA and store the secondary firmware image on an external flash using sQSPI. The project I started is based...
Hello,
We use the nrfx spis driver for communication between a ST processor (master) and a Fanstel BT840 module (nRF52840).
We have upgraded ncs from 2.6.0 to 3.2.1 and...
I am using a GPIO pin ( P1.05 ) as a reset signal for an external CPU component. The pin functions correctly and stays low when tested in a basic GPIO application. However...
I'm using NCS 3.2.4. When USE_PARTITION_MANAGER is active, the ARM linker script defines ROM_SIZE as PM_SIZE (the full app partition) without subtracting CONFIG_ROM_END_OFFSET...
To ensure fast and efficient ticket handling:
Please describe the problem as accurate and to-the-point as possible.
Include all the details needed to reproduce your situation...
Dear Nordic Engineer,
Hello!I am planning to develop a 2.4G, BLE and USB mouse. Both the dongle and the mouse device will use the NRF52840. I want to use BLE and ESB simultaneously...
Hello,
For my prject I need to tiggrer a timer start using a pin. I'm trying do do it using PPI but it seems that GPOITE can only create events on input pins. If anyone...
The MCU is NRF54L10, the SDK is NCS2.9.1, and the firmware is updated using MCUboot update mode.
Configuration as follows：
# sysbuild.conf
SB_CONFIG_BOOTLOADER_MCUBOOT...
Hi,
I write this information for the sake of completeness. I don´t need Zigbee2MQTT support from you. Instead, support with the Zigbee firmware is required.
I´m working...
Hello,
I am currently testing a setup combining the nRF5340DK and nRF7002EK using NCS/Toolchain v3.0.0 .
I need to reassign the 8 GPIO pins (including Bucken, Grant, etc...
