Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hello,
we have produced 10 Boards with nRF9151. Unfortunately, 3 device shows a false behavior. We cannot connect over SWD an they have a larger power consumption (whole...
Hello,
We are working with the nRF5340DK using nRF Connect SDK v2.9.1. Our firmware targets the nrf5340dk_nrf5340_cpuapp_ns board.
We would like to use P0.02 and P0.03...
Can anyone guide me the process of connecting multiple antennas with the nordic kit. I dont find exact information about the RF switch (GPIO-controlled antenna switches with...
Hi!
For a personal project, I am sending different sensor values to the nrf Cloud in JSON format which are visible on the terminal, but I want them to be stored as the...
A customer of ours is asking for a 3D model for NRF9161. They are trying to develop something on their end but cannot find the documentation showing the dimensions of the...
Hi.
I wonder if you could help me:
I'm using a thingy91x and would like to work with the npm1300. In the case of this hardware, the PMIC npm1300's i2c bus is connected...
We are using the NRF5340 with a Bluetooth transparent transmission example routine. We have set the connection interval to 7.5ms and the transmission timing to 3ms (sending...
Hello all, I'm currently developing some test FW for our custom hardware which include a nRF5340 and nRF7002, I made a small program to test the the different power supply...
We're trying out using devcontainers in WSL to develop Zephyr based software for our products. For flashing products from within the devcontainer we're connecting the corresponding...
Reference link: https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-9-bootloaders-and-dfu-fota/topic/exercise-1-dfu-over-uart/ I have an nRF54L15...
Hello everyone,
I'm working on a design using an nRF SoC and have a question about the correct way to handle I2C pull-up resistors in a mixed-voltage system.
My Setup...
Dear Nordic Support Team,
I’m encountering an issue during debugging where the code consistently hangs at line 360 in nrf_sdm.h , specifically at the following call:
...
Hi,
We are working with nRF52832. Over requirement is we need to transfer the file over BLE. We are using UART service (nus) to transfer file over BLE we getting maximum...
Hello,
I am working with a thingy9160 to connect to an MQTT broker using TLS.
I have run into an issue where the MQTT connection is disconnected with error code #XMQTTEVT...
Hi,
I have a nrf52833 with MCUBoot and BLE, I am using NCS v3.0.1.
I need also a custom NVS partition to store user data, so i create a data_partition for this purpose...
