i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Starting with the lbs example from lesson l4e2 of BT fundamentals course, I'd like to send an indication similar to the button (and keep the button). I basically created duplicates...
I am using the nRF9151-DK with the standard (from code examples) firmware . When configuring both P0.13 and P0.17 as ADC inputs, I notice that the current consumption on P0...
I am working with the connected_cs examples on the nRF54L15 DK and trying to swap the GAP roles. In my case:
Initiator = GAP Peripheral
Reflector = GAP Central...
I am working on a Bluetooth Low Energy (BLE) project using the nRF52840 Development Kit (DK) , which has been reconfigured to simulate an nRF52805 chip. The firmware is based...
How can you get the simple channel sounding test going with the bluetooth/cs shell commands?
I've got the shell working over UART and devices talking with each other but...
I tried to add external memory to mcuboot. In fact, I have successfully added it in app, but the same configuration seems to have problems in mcuboot ，mcuboot reports an error...
Hi,
We are developing a hardware and software solution for a locator tag using a minimalist approach. We want to use both, the Google Find Hub and Apple Find My Network...
I maintain an nRF52840 project on the legacy nRF5 SDK and am migrating to an nRF54L15 Bare Metal project.
I could not find a bare-metal “radio test” example, so I’m bootstrapping...
I do connect 52840 DK board to PC through USB cable, sine I want to see runtime log. but meanwhile, I want to use PPK2 to see the current of 52840 DK board, Can I get the...
Hi everyone, I noticed something unusual while testing BLE transmission and reception:
Transmitter: nRF5340DK
Receiver setups tested:
config：Target board...
Hi,
If I build the extxip_smp_svr sample app for the nrf5340dk board. The network image firmware version is set to 0.0.0.0.
To reproduce the issue, do the following...
In Lesson-3 Ex-2 for the BLE Fundamentals course, the steps for setting preferred PHY (steps 7 thru 9) is causing fault on my nRF52840-DK board.
Log messages are as follows...
Hi Nordic Team,
I'm currently working on integrating TagoIO using MQTT in our application. While attempting to add the MQTT connection details—specifically the username...
Hello,
I have a problem with a custom board using a nRF9151.
I can flash the nRF9151 and it seams to flash successfully (I tried with a blinky program and the leds start...
Hello, I am experiencing issues with the current measurements taken by the PPK2 when using the nPM2100-EK to power a device. The current drawn from the 2.7V power source ...
