I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
in the datasheet table 80 "GPIO port mapping" the function "CAN-RX" is only listed on P9.4 and P2.8 are these the only two pins it can be assigned to ?
I am struggling to...
Hi Dev,
Development platform: NRF54L15 + NCS 3.0.2. We use k_uptime_get() to obtain the system uptime and perform task scheduling. Everything runs normally when the device...
I need to create a firmware to the nRF9151 SMA DK that can send a message to me (it can be via MQTT, but I prefer the nRF Cloud) containing info about the location of the...
Hi,
I'm trying to debug a Zigbee issue and for that I want to try some Zigbee samples on the nRF52840DK. But all links for Zigbee in docs.nordicsemi seem to be broken. All...
I'm running into a bit of an annoying situation every time i run ' west flash --build-dir ./build' in the command line. It rebuilds always after a successful build i set when...
To anyone trying to create the reflector for this combination there is an important conf file to add to the project. You should add android_ranging.conf to your build that...
In NCS v3.3.0 the signing of binaries fails when building the Non-Secure application (build with TF-M) in combination with XIP, split images and disabled partition manager...
in Memfault I see the device ID number for each device such as 41EF6BB8FB6C9AF9. Is the distribution for the first 3 bytes the same as the distribution for the last 3 bytes...
Hello! I'm using Zepyhr OS with nrf connect SDK v3.2.3 and the NRF54L15 hardware.
I am using UARTE with the async driver (direct memory access). This is my uart configuration...
After a full consume of an spsc_pbuf , the buffer can become logically empty while rd_idx and wr_idx both remain at a non-zero offset. This breaks the next large allocation...
Dear Team,
We are currently using the nRF52833 as the BLE advertiser (cattle node) and the nRF5340 as the BLE scanner/gateway. The system is based on BLE Extended Advertising...
Hi,
I migrated my software from SDK11 TO SDK17
(Changed the BL + SD + APP)
Now i want to upgrade to (SDK17) old units (with SDK11) in the field.
Do you have any advise...
Hi There,
I am currently developing an LTE-M application on nrf9151 using ncs v3.2.1, the device is a MQTT client that publishes telemetry periodically every 3 minutes,...
I'm using nRF Connect for Desktop on Linux and updated today to v5.3.0.
I have J-Link V9.24a installed and it is available in $PATH. Also it works well with Programmer v4...
Hello, My nRF54L15-DK has suddenly stopped working, and it appears to have a hardware-level power failure.
The board was working normally the previous day while running...
