I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
Dear Nordic Team
nRF54L15 is advertised as supporting BLE 6.0. our product is a type of charging case,I would like to know if we need to pass BLE 6.0 certification?
If...
Hello,
Quick one:
https://docs.nordicsemi.com/r/bundle/nordic-mcp/page/index.html seems to be broken. I have a myNordic account and everything. I tried on two different...
I want to adjust the HFXO capacitance using INTCAP.
When the XOSC32MTRIM.SLOPE (chip-specific factory calibration value) is small, the resolution of INTCAP becomes coarse...
In our project we have functions for outputting a single frequency via PWM for an indefinite amount of time until we call a function to turn it off. See attached code.
...
I have a product which uses the nRF52840 SoC that will also have NFC functionality. The housing of the PCB is sort of forcing a custom design for the NFC Antenna.
We need...
Hi all,
I'm new to the nRF SDK and am currently tinkering around with my nRF52840DK to build a DIY Matter sensor. I copied the sample from the SDK, expanded it to my use...
Hi,
I am working on a custom nRF52840 design (using nRF Connect SDK v2.9.3) and I have accidentally locked the chip via APPROTECT.
My major issue is that on this hardware...
Hi, I am unable to read GPIOs (always getting 0x00000000 from gpio_port_get or 0 from gpio_pin_get). My main project is https://github.com/marcuswu/leaf-fall/tree/main/firmware...
After installing nrfutil-ble-sniffer v0.19.0 (released 2026-04-30) and running bootstrap, Wireshark does not show the "nRF Sniffer for Bluetooth LE" capture interface. The...
Hello everyone,
I'm working with the nRF5340 and I would like to connect a LIS2MDL sensor(see the schematic below).
The sensor has two power pins: VDD and VDD_IO . Initially...
I've been living with this for a while now, but it's getting annoying very quickly. I have a project in VS Code that uses the nRF Connect extension to build for nRF52832 and...
Hi
I want to use the FEM 21540 with nRF54LM20.
My overlay is :
My config is:
I think this should work because my nRF54L15 DK works well with this.
But it is...
Hello everyone,
I’m currently porting my old projects from NCS version 2.9.0 to 3.3.0.
In doing so, I no longer want to use the outdated Partition Manager; instead, I...
