I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Dear Team,
I have nRF54L15-DK and my firmware is running fine over there.
Now I want to use nRF54L15-DK to program & debug standalone NRF54L15 on a my custom board....
Our existing product (already in the market) at Element Science in San Francisco, CA, USA uses an nRF52832 (BMD-350 module by u-blox) and nRF5 SDK 15.3 as base for the firmware...
Hello, I have two nrf52840-dongles which I am using to test ESB. (NCS 3.1.1)
With a few modifications to the ESB prx and ptx samples:
Remove logs except for PTX ESB_EVENT_RX_RECEIVED...
I upgraded my sdk from 2.6.1 to 3.1.1 and after resolving a few issues everything was working just as it was before the upgrade except for MCUmgr. When I run the MCUmgr client...
Hi,
I recently migrated a project from NCS v2.x to NCS v3.x and noticed that the method I previously used to generate a device-unique identifier no longer works the same...
I've seen similar threads but haven't yet found an answer that works for me. I don't know much about encryption but I've been tasked with adding 256-bit AES GCM to our project...
On a BLE Peripheral NRF52840 built with nRF Connect SDK v3.0.2 , high-rate GATT notifications sometimes push the stack into a state where no (HCI 0x13) events arrive for the...
Dear Nordic support:
How long is the single broadcast duration and the broadcast interval for Bluetooth? We would like to know what the duty cycle of Bluetooth operation...
I am trying to Build a modified version of the Matter weather station with additional endpoints I have created a custom Cluster and Custom Device type via Matter Cluster editor...
Hi，nordic
My ncs verison is v3.1.0;
Can I use ANT+ and BLE protocol together in nrf54l05 ？
Does garmin have ANT for nRF Connect SDK support nrf54l15 dk now?
If I...
Hello,
I am looking for ways to measure current during the transmit and receive test for the 2NR modules.
Can you please provide me the steps to do that?
Also what application...
Greetings, I'm developing a custom hardware using nrf9151, i've tested the gpio and serial interfaces of the custom module and the work fine, when i try to flash the serial...
I am in trying to use the AT client sample with an RS485 interface on a custom Board with nrf9151.
Other than the API states ( https:/https://docs.zephyrproject.org/apidoc...
Hello,
I want to use only LDO (not DC/DC) regulation on my nRF52840 design. The documentation states that LDO is the default for both REG0 and REG1, and that DC/DC should...
