Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
It's been 14 months since the nRF 5x IoT SDK 0.9 was released.
Given Nordic's normal release cycle, that's an eternity!
Will there be another release or is it dead now...
Hello community,
Before I was using a pca10040 by Nordic evaluation board. The project, that i developed, is running well using the EB but when I change to sparkfun breakout...
Hello,
I'm working on nrf51822 with SDK9.0. I have two modules, one is working as a peripheral using s110 and another one is as a central using s130. Now central has a very...
Hi!
I am fairly new to programming micro controllers so apologies if I ask many questions.
I am using NRF52832. The situation is this - I have 2 devices and 1 host . After...
Hi all,
I've found the nRF52840 with USB but it seems a bit OTT for our application, something more like the 51822 would be nice, but cannot identify one, can anyone list...
Hello!
I have a code that is working perfectly on Eclipse for Linux and I would like to copy it to a windows computer with keil. I created a new project with Keil copying...
Hi, I'm developping endless PWM sequence.
That is ...
Only one output pin and the signal from it is repeated with the same period of pulse but with two different duty...
Greetings,
I'm having some trouble using the secure DFU bootloader and buttonless DFU service in my application. The code for both of these has been taken from their respective...
nRF52 SDK13 S132.
For example, I have handle from 0x180A service.
I want to read characteristic 0x2A24 from here.
How should do it?
In the watch window I can see event...
We are interfacing to a SPI Flash MX25R8035F.
When attempting to read 1 page of 256 bytes from the chip we break the read command up into 4 SPI Commands.
1) Read the Status...
Hi,
I`ve made fixes in SDK 13.0.0 files described below:
nrf_section.h : to supress gcc warning: invalid suffix on literal; C++11 requires a space between literal and...
When I set the PWM driver for very low frequency i can see how it blinks, the thing is that it always blinks where it's more or less 70% of the time ON and 30% OFF .
When...
Hello,
Working on a project using the pairing and bonding security model, I would like to filter out of a central's scan all already bonded peripheral devices. Or, I could...
For some reason I get a softreset instead of a sleepmode when I call sd_power_system_off();
Device: NRF52832
SDK: 12.2
S132 v 3.0
I do clear all gpiote interrupts...
