It flashes with sucess
C:\Users\vasco>openocd -f interface/stlink.cfg -f target/nrf52.cfg -c "program \"C:/Users/vasco/OneDrive/Ambiente de Trabalho/zephyr.hex\" verify...
Hi Team,
We are developing on a custom board with an nRF54L15 (Raytac Module with NRF54L15_xxAA_ENGB) and are unable to provision a pre-generated secp256r1 private key into...
Hi, I want to run Bluetooth Mesh Light example on nrf54h20 chip.
At the beginning I prepared devboard with this tutorial: https://docs.nordicsemi.com/bundle/ncs-latest/page...
Hello,
I am trying to build a firmware for the nRF5340 on the Thingy91:x. The firmware should use the external flash for the secondary Image and is using the chained bootload...
SDK: nRF Connect SDK v3.0.2
DK: nRF54L15-DK
Sample: spi_flash
default:
mspi-max-frequency = < DT_FREQ_M ( 8 )>;
If I change it to 32, it will printf these...
Hello,
I'm looking for answers and some explanation for two main questions - is it possible to perform non-simultaneous multi-image FOTA over WiFi? Is it possible to support...
As shown in the figure, MCUboot has a boot_go_hook function. I'd like to define this function in my own project and compile it into MCUboot. Since I'm using single slot DFU...
Hi all,
I'm currently learning on how to build bluetooth connections with a device from an app. For that I downloaded the iOS version of the nerf Toolbox app, as my chip...
hi
I am using nRF52 DK
Loaded Blinky Peripheral
I Connected this nRF DK to Com Port and Started Master Control Panel
But the Start Discovery Button is Disable. Please...
Hi,
I have an issue wherein once OTA update is complete through nRFToolbox (Toolbox says " Upload Complete") the Device does not reset and shows that it is connected to...
I am in the development stages of developing a ble application with the nrf52840 nordic chip.
I have come to realize the increasing difficulty of debugging this chip only...
Hello,
I made a custom board based on nRf52832, and I am using SDK 14.2
When I use a slightly modified version of the ble_app_uart example, I see it with nRf Toolbox,...
Hello,
I'm trying to configure 2 serial ports for a custom board with nRF52840 chip, but when I try to instance the second UART "NRF_SERIAL_UART_DEF(serial_uart1, 1);" the...
Hello,
I have an nRF52840 Preview DK, I would like to try the advertising extensions you introduced in the new released SDK.
My Goal is to make an application which send...
We're using a combination of the ESB library/example code and the USB CDC ADM example code to transfer data from one 52840 dev kit to another system via a 2nd 52840 dev kit...
I'm trying to build the gazell_dynamic pairing example for the host from the 14.2 SDK with GCC and I keep getting undefined references during the build process. I've added...
Hi,
I have modified nrf5-ble-mpu-data-ready-interrupts from nrf5-mpu-examples, the example works as expected. I have modified it a lot.
Now when I try to reconnect, it...
Hi,
We're running into a frustrating and tricky to debug issue with handling interrupts on the nrf52832. We have an active-low interrupt to pin 28, that is activated periodically...
Hi,
I just saw the errata for the nRf52840 Rev 1 and it seems Anomaly 197 ( DCDC of REG0 not functional ) and 202 ( Device does not start up in high voltage mode ) make...
Hello everyone
first if all, im not an expert in PWM, but doing my best to understand everything
I have successfully created and tested a project using the pwm_driver...
