I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
I just built nRF5 SDK for mesh v2.0.0 -> ‘light_switch_server_nrf52832_xxAA_s132_6.0.0’, but there is a compile error, "boards.h: No such file or directory".
My dev environment...
Helo, Im trying to sending data from sensor between two nrf52832, SDK 15.0.0 SoftDevice S140 on both. Im using uart central and peripheral examples on transmiter and receiver...
Hello,
Like in the description, I dont get this to work. Im trying to get The nRF24L01+ connected to a PIC16LF18345. I did Some Pictures of the SPI logic and Here is a Part...
I have the nRF52840 PDK and tried to download the firmware as per step 7 to paste it to the JLINK folder to make LED1 blink so i can test NFC but cannot get led 1 to blin...
I was wondering if adding a capacitor in parallel with the coin cell battery would help with the battery life by smoothing out the peaks. The scenario shown in the chart is...
Hello All,
I have successfully built the secure_bootloader app. I have the bootloader working with the button. I can upload application files using DFU. I tried the buttonless...
Hello
I'm currently running ble_app_uart__saadc_timer_driven__scan_mode and would like to modify it for faster sampling rate. However, NRF_ERROR_RESOURCE presents an obstacle...
Very new still learning.
I am using Keil and trying to setup the tools>customize tools menu.
Following the tutorial I am able to create the eraseall macro. No problem...
Hello~!
I am working on modifucation code of ble_app_uart example.
nRF51822
(SDK12.3.0_d7731ad)
Softdevice 130 (v2.0)
I know the original UUIDs are provided from...
Hi, I am working with the example Blinky_freertos present on the SDK_13.0.0_04a0bfd.
I have built the example w/o issues in compilation but I have the following problems...
Hi i get this error when compiling. (version 0.9.7)
I'm using arduino DUE and BLE Shield (redbearlab).
I get the error: EEPROM.h: No such file or directory in bootloader_setup...
I tried building ' pca10040 ' configuration of " nrf52-mpu-easydma-using-gpiote-and-registers " example from " https://github.com/Martinsbl/nrf5-mpu-examples ". The following...
Hi
I am working on nRF51-DK with Mbed IDE & used PWM example code from link : https://os.mbed.com/handbook/PwmOut
When enabled PwmOut, PWM signal is observed on the oscilloscope...
I would like advice on whether the following is a valid ble transaction.
We have a product with the nrf52 in it running sdk 12 and softdevice 3.0. This is setup as a a peripheral...
