Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Using a nRF51802, but can't find data about actual reset level other than min. VDD 1,8V ?? (Page 34 in datasheet )
I need to know actual reset level (VDD) for both rising...
Hi to all,
i am developing a device with NRF52840 DK, in my device i had implemented a service that has some characteristic with noti/read properties. notifications work...
Hi when I try create an account on www.nrfcloud.com on a desktop using Microsoft explorer it doesn't move forward and states "fetch" not defined. Any thoughts?
nRF Toolbox scanner code does not seem to discover devices which advertise a 128-bit service UUID.
I have extended the Template app (within nRF Toolbox) to interact with...
Hi to all,
i am developing a device with nrf52840 soc and i want connect to Windows 10 though ble connection. in my device i had implemented an HID service that should act...
Hey is it possible to use advertising beacons together with an server or there will be some collisions in message reception ?
what i want to do is: setup a mesh which consist...
Is there some guide to help implement UART using nRF Toolbox source code for ios?
I am trying to figure out how to use:
Scan, connect, pair and UART
Any help apprec...
when performing db discovering using a peripheral nrf52832 (running sample dfu project) from sdk 13 from a nrf32832 central on sdk 14 I notice that the db discovery event...
Hi Sir
I would want to download code to Ublox NINA-B301 by command line, but it looks not working, please help.
nrfjprog.exe -i 483064601
nrfjprog.exe --family NRF52...
Hi,
I'm trying to perform a DFU firmware update via command line using nrfutil dfu ble.
The same update using nRF connect works fine. The dongle is flashed with connectivity_1...
I would like to have a ZigBee stack running on the 52840 and use door/window (contact) sensors as well as motion (PIR) that are available on the market today to connect to...
Dear Sirs!
I use compiler IAR 7.80 with Nordic SDK 12.2
Softdevice
s132_nrf52_3.0.0_softdevice.hex
I have very strange issue in debugger.
Break point works, but...
Hi folks,
I try change blinky code for nRF52810 SoC. I must create own timer. I dont know app_timer example help for me?! I want to do when power on leds on 2 seconds...
Hi All,
I am developing an application in which i am interfacing the nRF52832 with an ADC via SPI.
I am doing channel multiplexing (2 channels) such that when i get data...
I'm aware of the limitations on using "printf" in a non-debug environment, but apparently there must be something similar with sprintf. I'm using it to load a value into a...
