But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hello, I currently using the proxy light switch exemple of the mesh SDK 2.0.1 in this configuration :
I search to have the less current consumption in the mesh client ....
Hi all,
Please find my following current measurement resuls in the pwr_mgmt example using a nRF52 preview DK and SDK 13
My setup is as follow:
SB40 is cut
SW6 is...
int main(void) { initialize(); execution_start(start);
for (;;) { (void)sd_app_evt_wait(); } }
can you explain me the execution of code flow in the main with these APIs...
Hi to all,
I am new i ble tech, i read some where that notification charactristic dose not need acknowledgement but indication need, now i want know that this acknowledgement...
Dear all developers：
I want to use whitelist on central mode，and using SDK12.3.0. I have see some call be used like this:
pm_whitelist_set（whitelist_load()）
p m_device_identities_list_set...
Hi,
We are working with SDK 15 with the HRS freeRTOS example. we did some modification to the advertising modes so that we advertise on fast mode for 1 minute and after...
Hi,
I'm using nRf52832 with SoftDevice S132 V3.0.
I found that I can exclude a bluetooth channel from the map by function sd_ble_opt_set .
But how can I tell that a...
When I compile the project (nrf5_SDK_for_Mesh_V2.0.1) exemple: Light_Switch....... there is an error that appears
#include "boards.h" --> (no such file or directory) Why...
I'm using SDK mesh v1.0.1 and nrf51822 S130 for mesh application. Light switch example is working fine. Now I want to add a twi sensor in server side. My doubt is in mesh...
Hello,
First, the current of the advertising frame was too high (around factor 2) and I have switched on the DC-DC to correct for that by inserting sd_power_dcdc_mode_set...
Where could i get the apk of thingy 52? it's hard for me to log on the Google play to install it because my phone didn't have GoogleServicesFramework, could anybody send me...
I am working on RTLS project. In beacon i am advertising battery life and temperature along with minor number and RSSI . I am merging battery strength and temperature in major...
Hi!
My setup:
* nRF52 DK
* nRF5_SDK_15.0.0_a53641a
* s132_nrf52_6.0.0
* SES V3.34b 64-bit
* android ver.8 smartphone with nRF Connect
I have implemented the...
Hello I'm using a macbookPro 2016 which only has usb-c and I can only connect the dk through a usb hub.
I have already installed the nrf5x-Command Line Tools for OSX but...
Hello everyone, i'm currently doing a project with nrf52832 and i just came across a problem. I configured 3 pins as output, then i set 2 pins to high and 1 pin to low. But...
