I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Hi,
The following vulnerability described as Bluetooth implementations may not sufficiently validate elliptic curve parameters during Diffie-Hellman key exchange in the...
I want to use the serial DFU. Do you have any examples? I tried with ble_app_buttonless_dfu, not UART DFU.If you have a detailed reference, please let me know.thank you very...
Hi,
I am using the MCU on a board with sensors that are sampled in a very high rate (~100Hz).
I am having issues when trying to send the data with notification on more...
Hi,
I am using sdk12.2 and customised nrf52 board.
I want to interface ultrasonic sensor with nrf52. In this I am enabling trigger pin as high and after sometime my...
Dear All,
I am working with SDK version 15 and softdevice 132.
I want the device to advertise for 1 minute. Then go to low power mode. Again wake up after 5 minutes...
I have twe NRF24L01 module,one set Tx mode with autoask,and another set Rx mode without autoask,
The channel and address are same.
Can I use this mode to communication...
I have problem flashing main program and SoftDevice on the nrf 51822 module. I have Keil version 5.24 and I am using SDK v12.3 .
I can flash SoftDevice easily but after...
Hi,
I init the UART pin with the AIN pin such as P0.05, but the program will run into __WEAK void app_error_fault_handler(uint32_t id, uint32_t pc, uint32_t info) every...
Hi Everyone
I have been trying to do some simple led blinking by generating events , however i need to do that if a button_0 is pressed for some duration.
Here is a code...
We are using SDK 15.0 and Softdevice 6.0, FreeRTOS 8.2.1
Is there a way to use softdevice and NRF_SDH_DISPATCH_MODEL_INTERRUPT?
If not, it means SDH task MUST be the highest...
Dear Sir,
I am using SDK15 and sodtdevice S132. I am testing on the kit BMD300.
I am using nRFConnect App in andoird to connect to the device and check the services...
Dear all,
I used SDK 12.3 buttonless functoin with PCA10028(nRF51422), and I occur some problem.
I did some testing as below:
case 1. softdevice+bootloader
case 2...
hi Nordic ,
I am developing an USB product with the nRF52840.
Can you can request the use of Nordic’s vendor ID in conjunction with an assigned unique Product ID?
Or...
Hi！
I read datasheet: nRF52840 Objective Product Specification v0.5. It says 52840. When SPI is master, it supports 32MSPI.
Which of the following examples can I refer...
Hey!
I'm migrating from Keil to Segger SES, is there any way to get a similar checkbox interface for sdk_config.h in SES like the configuration wizard in Keil?
Cheers...
