the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Is there any project idea that we can implement using the color sensor of nordic thingy:52.I have used apps like nordic thingy in my android device and nrf connect app.Using...
Hi,
I try to use the PPK to measure the current on my custom firmware.
The material:
PCA10028 (V1.1.0) with PCA63511 (rev 1.0.0 and rev 1.1.0) and nRF Connect V2.4.0...
Ok, Here is complete rewrite of " https://devzone.nordicsemi.com/f/nordic-q-a/36589/connect-to-nrf52832-central-mode-from-android-phone-pheripheral/"
I would like to update...
Hi,
Currently, I use the sdk 12.3.0 on a PCA10028 EVK with the s130 softdevice.
For some reason, I want to change the default location of my application. By default, the...
Hi...,
i have measured round trip delay from client to server.
Now I want to measure total time required to send message from server to client and client acknowledges...
I did current measurement for NRF52840. For mesh light switch demo example measurement was 10 mA, and for Thread CoAP Examples current measurement was 0,6 mA. I don't understand...
Hi all,
I am developing an application for a product where power consumption is critical. The application is bundled with the Secure DFU bootloader. I noticed that the bootloader...
Hello,
I think the question may be more related on how Wireshark works but I plan to do the following:
* use the v2 sniffer firmware and the Nordic Wireshark plugin
...
When I migrated, the reference routine output PWM, but kept reporting errors. I have also changed the relevant definition, but I still can't. Has anyone met it? Thank you...
Hello,
We're evaluating the Laird BL654 using your nRF52840 (to be precise, we're using two DVK-BL654-1.0 development kits).We tried to use the 'blinky' examples (ble_app_blinky_c...
Hi everyone,
I am developing a remote controller using nRF52832 chip. My prototype is currently developed in PC10040 board. The IDE is Eclipse Oxygen, and the SDK is S132...
Hello, everyone~
I plan to use the Low Energy Secure Connection funtion with nRF51822. But when I build the lesc example in SDK 12.3.0 (ble_multirole_lesc), there's a error...
Using the sdk15 and softdevice 132 v6, I'm setting up an app to read and write to an SD card that uses SPI1 (SPI0 is used by a display). Everything is working great, except...
Hi,
What's is the max length for the payload data in "mqttsn_packet_sender_publish" method?
EDIT:
Redefining my question above: What's is the max length for the payload...
Hi Sir,
According the table 19.4.2 of 52832 datasheet (v1.4), there is a start up time (0.36 ms) for HXFO.
How do I measure the start up time of my 32M crystal?
If...
