nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
Hi,
I'm using nrf52840,
I'm using SDK 15.
I can see that in nrf_drv_power_pof_init function only few power setting are allowed - is that true? can I only use those values...
Hi all,
I have a NRF52DK acting as a peripheral and running the ble_app_uart example. I want to have bi-directional communication with a mobile device that is connected...
Hi, I'm currently trying to make a flash logger using the nRF51822_XXAB. My logger is also advertising temperature, battery and other informations in beacon form. I also want...
mesh sdk: nrf5_SDK_for_Mesh_v1.0.1_src
example: light switch client + light swtich server
My problem is that the client cannot remove the server.
I found that many developers...
Hi All,
I am doing the certification (Japan Radio Law) now. I use the nRFgo software to enter the "Direct Test Mode" for test the each channel BUT I do not know how to...
I have designed nrf52832 customized board with tace antenna antenna and every pin of the controller is connected to the male headers present on both side of the boards. I...
I am using sdk 14.2.0 and I want to use nrf_calendar.h in my code but it is supported only in sdk 13.0.
will you guide me how can I use it in my sdk version 14.2.0.
the...
Hi,
Would someone please help me to configure a specif channel for continuous scanning. I was browsing through the forums and understand that the SDK/SD not supports these...
Hi together,
since quite some time I try to merge my BLE application with the SPIS functionalities from nRF52 SDK 12.3 example with softdevice S132. My application should...
Hi, I am developing a central device application using the ble_app_multirole_lesc example as a baseline. I am using v11 of the SDK. This example uses the heart rate service...
I am following the Thread Border Router example and have successfully loaded RaspPi_OT_Border_Router_Demo_v1.0.0-1.alpha.img onto the RaspberryPi 3B+.
I have loaded the...
Scan of services after connecting to DFUTarg does not return
the new services on the device. Instead the old services that existed
on the device before going into DFU...
I'm trying to follow the guide Sending mesh packets in the Interactive PyACI section on the nordic infocenter.
I've installed the required prerequisites using pip.
Here...
SDK 14.2
This question pertains to the app_timer library.
Hi,
I am using the app_timer library for creating/starting timeouts.I had a question about the APP_TIMER_MIN_TIMEOUT_TICKS...
