Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hi Sir,
We got the nRF52833-DK, and tried to program the nRF52832 IC through the nRF52833-DK.
We download the latest version of nRF connect and command line tool, but...
Dear,
I am using THINGY:91
I am trying to read the data from BME680 sensor:
1. config: ( i used conf file from asset_tracking)
and, get the temperature:
...
Hello,
I am using UART1 to communicate with sensor. It is working fine. I can receive the data. Now I want to modify this data. When I use strcpy() function, it works properly...
Hi Team,
We are trying to make Nordic NRF52840DK board to act as a server (BLE ) where as we are trying to connect other board (Not the Nordic chip) has only transmitter...
Hello again, I accidently verified one of my own answer so I will retry.
I am currently trying to update the firmware for Thingy 52, using the NRF52 development kit. ...
I'm using a nrf52840dk as peripheral and iOS (iPhone 8) as a central. They are to be paired. The pairing routine is already implemented and works fine. The problem is that...
Update: Was me being a dumb ass and calling the advertising start higher up in code that I thought I disabled. After truly disabling the BLE, I was able to debug and found...
Hi,
Overview: In our board BMD340 (containing nRF52840) module present with GSM module and they exchange data using UART(PINRX-6,PINTX-7). Now we trying to use "ble_app_uart...
hi,
i am using one central and 18 peripherals. i am unable to send data to one particular peripheral from the central .plz help me to identify a peripheral in the group...
Hello, We were interested in a new SoC nRF5340, but I would like to determine some points in advance:
peripheral blocks remained the same as in nrf52840. Or were changes...
Hi there,
I would like to add the device address of a central to the whitelist on my peripheral. Is this possible without bonding? So I set sec_param.bond = false in pm_sec_params_set...
Hello.
I am working on ble project and using uart communication between bluetooth and stm32. I need to reinitialize uart module in case of any error in event handler but...
1、nRF52830。Does the dongle included with the product support the over the air packet capturing function of Bluetooth?
2、We need Bluetooth to grab packets. Do we need a third...
Hello,
nRF52840-DK
SDK: 15.3.0
s140
OS: Ubuntu
IDE: SES
Our application is has a notify characteristic that works when attached to the JLink debugger. I can get...
Hi, I am using nRF51822 on my custom board with SDK 12.2.0. I use DFU bootloader, and can update application in BLE from DFU mode with bootloader (dual bank mode is used)...
