It is nRF54L15 + SDK 3.0 + Matter application.
I have developed a custom BLE service that is based on Nordic's proprietary NUS BLE service. The BLE custom service is enabled...
I am trying to get a WiFi project working using the nRF52840DK and nRF7002EK . I use a 3.3V power source that is supplying power to both nRF's in parallel. For the nRF7002EK...
Hi,
I'm developing firmware for the nRF52840 DK using nRF Connect SDK v2.9.2 , and I’m running into a problem that didn’t occur in v2.8.0 .
My project uses Zephyr and...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
We have previously used nRF52840 and for the latest iteration of our board design we are updating to use nRF54L15.
We are aware that for nRF52840 we could map any pin to...
Hi,
I faced with an initialization issue of combination two features: MCUMGR and UART_ASYNC_API. I get a crash right after the FW starts. It looks like the SW configuration...
I checked the nrf52832 manual and found that both XC1 and CX2 are analog input pins for the 32Mhz clock pin configuration. The reference design for both uses 32Mhz crystals...
Hi,
As far as I understand, every connection establishment has to start with advertising.
Event if I have already connected and bonded to a peer, after disconnection...
Hi everyone,
I am using an nRF52840 dongle (MakerDiary) with SDK15.0 & SoftDevice S140 v6.0.0, and trying to change the BLE advertising manufacturer's data with the information...
Hi,
I am sampling a moisture sensor using one of the analog pins without issues. However, since my circuit is battery powered, I need to account for voltage drop of a 3V...
I have an nrf9160 dk on the latest firmware (i.e. mfw_nrf9160_1.1.1) and I have been unable to establish stable connection to LTE network using iBasis SIM. I tried using the...
Hi,
I am trying to follow this tutorial ( https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/getting-started-cellular/posts/ncs-tutorial---temporary ) on Nordic...
Hi,
I am facing the same issue of case 244574 , we tried to fix it follow your advice but failed. Here is my code:
After the first reboot of modem FOTA, the application...
Hi,
Recently updated with " nRF Connect SDK V1.2", after that AT Commands is working only with nRF connect link monitor SW. Its not working with teraterm,putty. In tera...
Hi
I am using the SDK_16.0.0 and SDK_for_mesh_4.0.
Board: PCA10056, nRF52840.
1) I try to send strings to from the nRF to PC and then, using a python script, poll...
Hello,
I started working on 802_15_4 to create a TSCH ( Time SYNC channel hopping ), and it is working as expected. The problem is when i integrated the TSCH TX and TSCH...
Hi,
I want to create a file and save it to device storage or my computer.
As a result, I want to save a large amount of data in a text file, compress it, and send it to...
I'm having some issues with the printing to the debug terminal. I'm using SDK16 with SES 4.5 and developing on the nrf52840 DK.
I followed the instructions in this video...
I bought a pack of Vodafone NB-IoT SIMS from Arkessa for use in London, UK as there is currently no LTE-M availability where I live.
Arkessa have provided the following...
Hi,
If I don't configure GPIO pin (for LED), the led is not lit, and it doesn't draw any current. (16uA).
But If I configured it as output, then disconnect, OR output...
Hi,
i need to Stop the softdivice in my application with --> sd_softdevice_disable ( );
This is ok, it works. But later in the applictaion i have to restart or enable...