Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hi,
I am looking for (andriod) mobile phone that support Bluetooth LE coded (long range)
Have you ever tested bluetooth (LE coded) with mobile phone ?
Please recommend...
I am currently developing firmware that needs to run on both 32 and 40 chips.
The basics of the situation is the firmware contains 3 'applications'. A flag in the UICR region...
Hello,
I have been looking through the SDK for the Thingy:52, and I have been unable to find the configuration file used for the MPU-9250. I am able to see the default pedometer...
I use QSPI to access MT25qu512 serial flash and find the following behavior.
SDK: nRF5_SDK_15.3.0_59ac345
QSPI configuration:
// Use 4 bytes address from serial flash...
I am unable to figure out what causes the problem that IRQ handler is defined both in nrfx_uart and nrfx_uarte modules.
After investigating in a test project I have found...
I have previously built the Asset Tracker downloaded it to my 9160DK with no problems.
Today I connected my Thingy91 and updated it's firmware. Afterwards I built the Asset...
Hello,
I'm trying to create a Mesh network with the following devices:
* Mobile phone as provisioner (supports PB-GATT only)
* Two different bulb's which supports PB...
When storing entries that aren't multiple of 4 bytes they are padded with random bytes by flash manager.
The problem is that they aren't padded with 1's but rather random...
I'm testing with a Custom board using a nrf52832 chip.
Testing BLE communication using nRF Tool Box.
I am using SDK15.3.0 example for communication using nRF Toolbox and...
Hi,
I am trying to install the nrf command line tools on linux. After following the installation instruction, I have the error
ERROR: nrfjprog.ini not found. Please reinstall...
Received the IN-119 notice, and it says:
All users are recommended to use the latest release of BLE protocol stack software for product development. All BLE protocol stacks...
Hi,
Using SDK 15.2.0 and SD S140_6_1_1.
I have two hardware of nRF52840, one has external LF crystal(32kHz) and another does not.
Want to run same firmware file in...
Hi i have questions about nrf52832 and nrf52811 soc.
Currently we are selling custom board with nrf52832 soc which works fine and going out for sale
In the custom...
Hello,
this is a brief description of my plans:
I am planning on merging my modified ble rscs central example that is used as a cycling cadence central device instead...
