I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
I use S130 on two nrf51822/PCA10001 boards. Each nRF scans and advertises simultaneously.
Scan parameters are:
scan_param.active = 0;
scan_param.selective = 0;
scan_param...
Is there a port of lib_aci for 16-bit processors? The structs in lib_aci written for nRF8200 are byte misaligned using a 16-bit processor. Seems to be almost a complete rewrite...
Hello,
I try to generate 4 PWM signals on an nRF51 DK board, but I have two troubles :
in the "Simple PWM", during nrf_pwm_set_value() function the TIMER is stopped...
Hi,
I recently ordered a usb dongle. It has PCA10031 board. The chip shows "N51422 QF ACAB" printed on it.
What SDK should I use? 6.1.0?
What board file should...
Hi!
I am using nRF51 SDK v6.10. I try to analysis the "spi_master_example". Source codes is
working well. But I couldn't understand how the "spi_master_send_recv_irq(...
I have an android application, which one can set and unset the LEDs of my nRF51422 EK. But sometimes when I click to fast the command will not be send. So I would like to...
Hello,
I want to know if it is possible to configure a button to act with different Detection delay.
In other words I want to have a single button to be able to trigger...
Do we have KiCad version of nRF51822 QFN48 reference design? We looking at open source toolkits, including Eclipse, so KiCad comes into picture.
Thank you in advance!
The test code:
int main(void)
{
sd_softdevice_enable(NRF_CLOCK_LFCLKSRC_RC_250_PPM_250MS_CALIBRATION, softdevice_assertion_handle);
temp_init();
unsigned int aaa...
I have a follow-up to this question: devzone.nordicsemi.com/.../
We are interested in dynamically changing the supply voltage because our space-constrained design requires...
Hi,
For my custom PCB, I am using the PCA10004 as reference in order to determine if the maximum possible range has been achieved. However, I am seeing only about 20 feet...
Hello I'v just ordered a NRF51-DK kit.
I'm looking at the different tool chain. In my application speed is critical 16Mhz is actually bearly enough, so my question is:...
I have a USB dongle with an nRF24LU1p that has a few SPI pins but is missing the RESET pin. I would like to be able to program it via SPI but the SPI programming protocol...
nRF51 RTX 4.74.0-3
SoftDevice S210 V4.0.1-3
Created a timer for 5 seconds interval.
It turned to be 4.4 seconds. with or without softdevice enabled.
Anybody else has...
Hi,
Access to the UART hangs the execution of the experimental_ble_app_uart_s110_pca10028 example.
The phenomen occures In the file simple_uart.c when checking for the...
