Hi Nordic team,
We are planning to use the STM32H747 as the host MCU to control the nRF7002 for Wi-Fi functionality. Based on reference materials and existing use cases...
Hello Nordic team,
I am working with the nRF54H20 and would like to integrate both Enhanced ShockBurst (ESB PTX) and Bluetooth Low Energy (BLE peripheral) protocols in my...
Hello, I'm testing the nRF21540 FEM on a custom nRF52840-based board using the nRF Connect SDK.
I’ve enabled CONFIG_MPSL_FEM CONFIG_MPSL_FEM_NRF21540_GPIO_SPI CONFIG_BT_LL_SOFTDEVICE...
Hello, checking if I'm doing this right of restoring initial fw for 91X to work with Quick Start v1.2.0. as described here in Get Started, https://www.nordicsemi.com/Products...
It is nRF54L15 + SDK 3.0 + Matter application.
I have developed a custom BLE service that is based on Nordic's proprietary NUS BLE service. The BLE custom service is enabled...
Background
For reasons that I do not want to dispute here, I am building a custom bootloader for the APP + NET cores on the nRF5340. This custom bootloader is not a Zephyr...
I am testing out the nRF54H20 on the nRF54H20-DK version 0.9.1. I have followed the steps for setup in the "Getting started with the nRF54H20 DK". I currently have nrf54h20_soc_binaries_v0...
I want to write a program in Keil by SPP for communicating with a thermal printer that uses SPP
but I can't find source code about that.
Is this possible to do this with...
Hello
i have nrf52 PAC10036 dev Board.
i am using the visualgdb.
when i try to create the instance of the TWI.
i got the error
please check image for detail.
How i can...
I want to turn off BLE-peripheral Advertising for 8 hours but I want to use another timer with period of 50ms to scan GPIO ,
when I change prescale of
APP_TIMER_INIT(APP_TIMER_PRESCALER...
Hello,
is there a good documenation or introduction about the Programmable Peripheral Interconnect Feature? I read the short part in the Objective Product Specification...
Hi everyone,
I need to use an nRF51822 (MBH7BLZ07-109033) mounted on a custom board.
I want to develop my firmware application on the custom board in such a way I can...
Hello,
I am using nrf51822 doing projects. I met an issuse which is that at the first 6 minutes, it can normaly go into UART interrupt and run subroutine successfully....
I'm testing out TWI on pins 24/25 and I get a crash when I attempt to do a TWI transfer and I find myself in: WDT_IRQHandler ()
I'm using much of the example code:
APP_TWI_INIT...
Hello, I have a few nRF devices, and I am unsure as to which revision the ICs are. Here are the three HWIDs:
0x00AE,
0x0086, and
0x0077
I tried looking into the nRF51_Series_Compatibility_Matrix_v2...
Hi,
I need to sample 2 inputs at 200Hz and send it on an app. Can I send the data at this speed using UART service? I was trying to do it using HRM example but could not...
Hi, I am trying to compile the code
github.com/.../main.c.
I need to include the header file uart_confg.h, can someone tell me where I can find it in the sdk 10 component...
Hi,
I wrote a program that uses ESB communication between two nodes. On both sides I use the same ESB configuration and the same ESB init function, the difference is only...
Hello,
Environment: nRF51DK + SDK8
We've developed the beacon application but the advertising interval is set to 5 seconds. The beacon can be discovered by nRF Connect...
I have searched here on the DevZone, and also around the web, and don't see this issue mentioned elsewhere. I really appreciate any help finding a solution.
I tried following...
Hi All,
I think I noticed a bug in the nRF Connect v1.0 application. The Scan Response data is not shown in the Windows application. When I scan the device with the iPhone...
