Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello,
I do communications between 2 nRF51822 (one central and one device). Once they are connected, cant i do a kind of deep sleep and freeze stack state for 1 minute...
I'm getting a hardfault on some float operations that I wasn't getting before I upgraded to SDK 6.0.0 and SD 7.0.0. At least, I wasn't getting them at all before that and...
Hi:
I use spi0(0x40003000) to wirte data to external flash(W25Q64) with SD8.0(sdk8.0.if I write data without sd, it is OK), and when program run to rx_data[number_of_txd_bytes...
A friend of mine asked me to help with thinking about a solution to create a RF communication between 8 robots and 1 access point. Not a lot of traffic, just to signal that...
Hi everyone,
We are making a BLE peripheral that measures some data and keeps it ready for the mobile phone to connect & poll the data.
The data should be private and...
I am trying to use the template to create my own application. In two places I have read, that to add my own services, I just "Double-click the Serives folder in the Project...
Hello everyone,
I had some troubles some time ago with Softdevice s120, and finally solved it to work with nRF51822 thanks to Aryan .
The problem is that, when I upload...
I'm following the official tutorial for using pstorage and this the simplest test code I've come up with:
static pstorage_handle_t base_handle;
static void test_pstorage_cb_handler...
Hi
i started some time ago with building a simple peripheral device, and started form the led-button service example.
In there, device manager was not used. However, in...
Hi,
My application receives assert error from stack. Source file name is src\ll_master.c, line number 831 and error code 0xDEADBEEF.
What this error signifies?
R...
Hello,
In my application I'm using SDK 8.1 with the s110 SoftDevice. In the new version, the pstorage modules have been separated and you need to choose between them.
...
Trying to see how much time my code consumes, I tried the naive approach, calling clock() in the beginning and at the end and comparing the values.
But when I include clock...
I am using the BLE Scanner app on Android to check that my device works.
I have 2 similar problems :
on one device, I can read all characteristics except one. This has...
Hi,
Im trying to use this example to send serial data from GPS module via BLE:
github.com/.../ble_app_uart_low_power_slave
I have disabled hardware flow control since...
Hi
I tried gateway and LED_mesh examples. It worked well. But, I found some issues as below.
When I tired MCP windows application on laptop with PCA10031 dongle...
