Hi,
I'm using the nRF52833 to develop a BLE beacon and built a Bluetooth gateway for my application.
Application Requirements:
The beacon should advertise using...
Hello,
I want to perform some antenna measurements and compare the rf performance of my custom PCB with an nrf9160 SiP with the nrf9160 dk.
To perform some antenna measurements...
Hello - I have the exact same question as proposed in this thread - I am wondering if there has been any change in the 3 last years since it was posted.
In a nutshell, we...
Hi I want to build a multi role BLE device.
As a peripheral it shall stream ADC data with arounf 20 kbytes per second.
As Central it shall receive adv_nonconn_ind packets...
Hello everyone,
I have an nRF5340 microcontroller (NORA B106 module), and I want to connect a square wave signal to one of its pins to read its frequency or count the number...
Hi,
Hope you are doing well.
I would like to use eSIM on nRF9151-DK board and an eSIM has been assembled in the board. However, eSIM is not detected.
According to...
Dear Nordic Engineers
I developed a PWM function to drive the RGB LED. Then I found a problem, which is w hen I used a PWM signal of one channel to control the RED light...
The bluetooth of android APP is easy to disconnect (we make smart door lock products); The product is delivered to the customer. It is easy to disconnect and not connect with...
Hello,
I learnt about some resource pre-allocation in the datasheet, e.g. ppi, or API documentation, e.g. app_timer rtc1. I see the SDK drivers are trying to take care some...
SDK16, S112, 52810. I have DCDC set up and external 32.768 crystal oscillator on my board.
Here is my code part:
main()
nrf_power_dcdcen_set(true); nrf_delay_ms(100...
Dear ,
Follow the previous ticket, https://devzone.nordicsemi.com/f/nordic-q-a/59034/agps_thingy91
I am trying to use asset_tracker : https://github.com/NordicPlayground...
I am writing an application on a BLE chip that will transmit high volumes of data to an Android phone (520,000 bytes / second signal).
According to some tests I've seen...
my board uses 51822. I am using 52DK to debug it. I have plugged my board with 52DK as following:
RX -> p0.08
TX -> p0.06
My question is, when I init UART in code...
Device: nrf9160 (dk and custom board)
sample application : MQTT simple
segger studio (nordic version): V4.42a
There are 2 main issues:
1) in the main.c file, Segger...
Last time I used it, it worked fine, it's been sitting in a drawer for some time since then.
When I tried to use it now, i get this error - even though I can read the...
Hi team Nordic,
Looking in the nrf53 datasheet, it seems like the PDM clocks are the same (peripheral) as the nrf52, is this correct?
You usually wanna run the newer high...
Hello,
I am using an nRF52840 on a custom board, and I want to add the workaround for Errata [87] Unexpected wake from System ON Idle when using FPU . However, the the...
Hi,
I´m trying to flash a custom board with nrf52833 chip with the nrf82833 DK.
How can i make sure, that tha DK board will program the custom board? Currently it...
Why isn't this working?
The MPU_RESET_PIN is set to : NRF_GPIO_PIN_MAP( 0 , 20 )
I can not seem to be able to alter the state of the PIN. Whenever I read the PIN its...
Hello all!
I have a timer that sometimes gets started inside the IRQ of the ESB and sometimes needs to be restarted inside its own IRQ
I'm running it in a "one shot...
Hello
This parameter must be modified e.g. if you have a large number of characteristic in your custom service.
is there a reasoning to calculate this or just "try and...
