Nordic TS,
I've installed and begin to experiment with the DECT NR+ v1.1.1.0 FW. Initially, I'm noticing on obvious difference in the behavior of the dect_hello sample between...
I am trying to use the FIFO from the ADXL362 with in the Thingy:53. As I noticed there is now the Option to use ADXL362_STREAM. I just wanted to use the example from: https...
The specification for the nRF54L15 states that the typical current consumption for I_TIMER3 (TIMER10 running) is 240 mA/milliamps . The other timer values in the table are...
The Nordic Thingy:91X was initially unable to connect using certain SIMs (e.g., Airtel IoT) due to lack of NB-IoT support or no signal.
After switching to a Jio NB-IoT...
Hi to all,
I am trying to do a ZUTH (Zigbee unified test harness) test run, using the Silabs devices as golden devices (as per CSA recommendation) and nRF 52840 dongles...
Hi
I am trying to port some PWM code from the NRF54L15 it uses HAL access because i have found it has faster writes which are useful for my application (testing latency...
Hello Sir
Sir i am try to sending the some text to nrf 52840 board,if you have any document please send it.
and how to do this process ? Sir please explain
Hi ;
If there is a ble message coming , but this time ble is getting data from sensor , what will happen ? Will it device reset ? Would you give me any idea to avoid this...
Dear all,
We have a question.
Did any body tried to make so that Bluetooth Mesh 4.2 works in PARALLEL with Bluetooth 5.
Some schedule reserved for BLE MESH 4.2 and some...
Hello,
I never used BT modules before. I'm going to buy some bluetooth modules to add wireless to an existing board.
I need module with following characteristics:...
Hi，I want to write the firmware to 52832 from android system by UART .I have readed the firmware into bytes, and then do not know how to compose the bytes to write into serial...
I have the following situation:
My device receives a number of RF packets, changes to TX mode, sends some data, goes back to RX mode and it should be able to access the...
Hi,
my application is normally a BLE scanner, listening for beacons. This runs OK.
Now, I tried to add a tested piece of connectable gap/gatt firmware, that runs fine...
Hi ,
in the RTOS example, you set
configTICK_SOURCE as FREERTOS_USE_RTC and configCPU_CLOCK_HZ as( SystemCoreClock ) .Since SystemCoreClock is 64mhz, why did you not set...
I am trying to understand why when I connect the nRF52840 Dongle using nRF Desktop I get this message in the log:
2020-02-26T23:12:13.293Z INFO Connectivity firmware version...
Hi Team,
We are using nRF 52840 chip for our development of product.
As of now the settings for BLE data transfer are as below.
MIN_CONN_INTERVAL 20 // which is the...
Hi,
I'm developing a router Zigbee device starting from light bulb example.
In the example the function zb_set_max_children is called passing 10 as parameter.
About...
Hi,
I am using
PCA10056
SDK 15.3.0
Keil IDE
The soft device is S140
JLinkRTTViewer for debug
I am testing background serial-dfu.(refer to https://devzone...
Hello,
We are working with the nrf 9160 dk.
We need to use internet connectivity to send an http get and post to a remote server.
We want to utilize the NB-IoT...
I've been developing firmware for my PCA10059.
I load the package with nrfutil dfu usb-serial --package=_build/t.zip --serial-number=`cat /tmp/serials.txt` --connect-delay...
